• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by want 2 get high

  1. W

    Hold valve removal question

    I have a JLG 45ic lift. I have the mid cylinder staying extended. What is the procedure for removing the hold valve to release the oil pressure holding the cylinder in the up position? I had the lift in the full up position and when I came back down the mid cylinder would not come down. Thanks...
  2. W

    Addco throttle control issue on JLG 45IC lift

    Hello willie59. Like I said in the original post the addco throttle control has a red light come on if the foot peddle and than controls are not used very soon after the power knob is pulled out while in the basket. Than you have to push the power knob back in again, and pull it out to get the...
  3. W

    Addco throttle control issue on JLG 45IC lift

    Input anyone?
  4. W

    Addco throttle control issue on JLG 45IC lift

    Hello all, Does the addco throttle control have a time out circuit on the JLG 45IC lift. If I start the lift on the ground switch it runs the idle up as it should and stays that way. If I switch to the basket and don't immediately step on the foot peddle and start using the controls the addco...
  5. W

    98 JLG 45IC lift

    Hi all, having another issue with the lift. Here lately the throttle control module is acting up. While in the basket if you do not use the controls with in a short amount of time the control module goes to a red light. If you push the control button to off and then pull it back out you can then...
  6. W

    another ? on a JLG 45ic lift

    So after doing some checking with a test light and a V/O meter and not coming up with anything I removed the sensor at which point I thought I heard a click. Tapped the sensor on a piece of wood a few time in the direction that would close it and put it back in. No more warning light or beeper...
  7. W

    another ? on a JLG 45ic lift

    So I checked today and there are 3 wires running to the sensor.
  8. W

    another ? on a JLG 45ic lift

    I will have to look. I know the sensor has 4 prongs but I did not pay attention to the number of wires that run to the plug. I will look tomorrow and post. Thanks for the reply.
  9. W

    another ? on a JLG 45ic lift

    So my lift has a warning light and alarm on. It is for the trans filter bypass. I changed out the filter thinking it was clogged. No change. Any thoughts on what my next check should be. Does the sensor on top of the filter housing need to be reset? Any and all help is appreciated
  10. W

    98 JLG 45IC lift

    Thank you for the replies.
  11. W

    98 JLG 45IC lift

    80 views and not a single answer? Surely someone knows if a JLG lift comes with a title.
  12. W

    98 JLG 45IC lift

    Didn't think this was such a hard question. Would like to find out if the lift I bought should have a title. Can anyone help?
  13. W

    98 JLG 45IC lift

    Do these machines have a title that goes with when it is sold?
  14. W

    JLG45IC Engine RPM while in basket.

    Up date. After reading another thread involving rpm and looking through the wiring diagram I came to the conclusion I needed a controller. I was getting power to the controller from the both ground and basket controls but the controller was not doing anything with it. 500.00 later the JLG is...
  15. W

    JLG 600AJ Deutz Year 2000

    I know this is an old thread and I have a JLG 45IC but I am hoping to make use of this information to track down the RPM issue with my lift. Thank you for your time and help.
See more
Top