• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. R

    2015 Hino 258 RPM run away

    Okay, I have a problem with my 2015 Hino 258 rollback tow truck. Issue started yesterday. When I start up the truck after about a minute of idle the engine RPM instantly goes to 3000, no way of stopping it, I just need to turn the key off. It only does this when in neutral. Another example is...
  2. R

    2005 Nissan UD 2300 limp mode

    Hello I have a 2005 Nissan UD that is going into limp mode I have followed the manufacturers instructions to activate the check engine light flash sequence I have grounded the engine diagnostic wire then turn the key to the on position the check engine light will flash 8 times however there is...
  3. R

    Help: old yale-er lift cylinder removal

    So it's time to put seals in my yale, it's a GC030UA I think from the mid to late 70's. I've not dealt with this type of cylinder before where it is attached near the bottom on pivot pins. How do I get it separated from the gantry? I am trying to up load a photo but its not letting me?
  4. R

    International engine swap?

    Hello, I have a 2001 international rollback with a DT530 with a standard transmission behind it, engine went bad.... I have a cummins L10 on the side. I've heard the internationals came with the L10's, has anyone ever swapped one into a DT truck? Thanks!
  5. R

    No start. Komatsu PC50

    2006 PC50mr-2 The other day the dash/display was randomly beeping while I was operating. I noticed some moisture under the cover. I removed it and dried it. Re-installed it, and it seems fine, all the functions work, went to start the machine and I just get a relay clicking when I turn the...
  6. R

    Internationl 100E track loader seal kit?

    Hello, I have a International 100E track loader. Does anyone know the part number for a seal kit for the top tilt ram cylinders? and where I could order it online? Thank you!
  7. R

    Shoud I purchase an International TD25

    I am thinking about buying a 1979 International TD25 for $10,000. the machine looks good, runs good. has a ripper on the rear, tilt blade..... I know nothing about these machines, are they any good, are parts available, is there any known problems? about how heavy is the machine? I just need to...
  8. R

    Anyone with a part numbers? International 100e track loader

    Hi, My machine is an International 100E. I am trying to have my hydraulic rams rebuilt. the ones on the top side left and right of the hood. For some reason the hydraulic shop cannot find the proper seals for the rams. It has been over a year and I would really like to use my machine again...
  9. R

    Sticky track control? PC50

    2007 Komatsu PC50 all of a sudden my left track control lever is hard to move and it sticks in whatever position you leave it in, which is nice if i wanted cruise control, but in actually, its a pain in the ass. one day it worked fine, left the machine on the job, rained hard the next few...
  10. R

    Wanted: Mini excavator hammer

    I am looking to buy a hammer to put onto my Komatsu PC50. thank you.
  11. R

    Is there a Forklift section?

    I need help with a Hyster Forklift. Is there a section on this forum or can someone point me to a forum that could help? Trying to find out year, make, model of a Hyster and I also have a problem with it. The lifting ram has a hard time coming down, it is newly rebuilt. I followed the two lines...
  12. R

    Komatsu PC50MR-2 where is the travel buzzer located

    I am trying to locate the travel buzzer or travel alarm. It goes beep beep beep when ever you go forward or reverse. The machine is a 2004 pc50mr-2. Thanks.
  13. R

    Komatsu PC50MR-2 has slow side swing?

    2004 pc50mr-2 has slow side swing. 2500hrs, everything else works flawlessly, boom up/down/out/in, bucket in/out, blade up/down all perfect. we timed the cab doing 360 rotations and it was 6 seconds slower then it should be. any ideas?
  14. R

    What hydraulic fluid to use?

    Hi, I have a grey market Kobelco SK030. What weight hydraulic fluid should I be using? Currently I have ISO46 in it, will it matter if I put ISO68 or ISO32. The machine is being operated in Hawaii. Thank you.
  15. R

    D9G Injector

    I am looking to purchase 1 injector from a D9G. It does not need to work, I am going to drill it out and weld a grease fitting to the top. Thank you.
  16. R

    CAT D9G 66A frozen motor

    I have an old CAT D9G 66A. The engine is frozen, water got in and has stuck the rings to the cylinder walls. Does anyone know where I could find a breaker bar that fits into the pony motor hole. The ring gear is angle cut. I know there is a breaker bar for the straight cut ring gear, but how...
  17. R

    Cat 302.5 no side swing power?

    A friend of mine has a Cat 302.5, all the hydraulics work great except when I place the bucket on the ground and try to side grade. If the bucket touches the ground at all, it will not rotate. in fact it won't even move a 18" rock to the side. The owner said it will, but you have to hit it like...
  18. R

    Right side track slower then left?

    Alright, I drove my machine today. New problem?? The new drive motor, on the right track is a lot slower then the left track? do drive motors have left and right? there was 4 ports on the drive motor for hydraulic lines. 3 were used one is plugged. When I installed the unit, the top one was...
  19. R

    What Brand of Hammer is this?

    Trying to find out who makes this hammer in case I need to buy parts or rebuild it I can. It looks like someone has welded two extra tabs on top of it for mounting on a different machine. If anyone knows, please reply. Thank you.
  20. R

    How do I fill oil in my drive motor?

    I have attached a picture. There is two plugs on my drive motor. One says OIL L. which I assume is the Oil Fill hole it is if positioned at 12 o'clock is about 3/4 way up the face. The other if positioned at the bottom, 6 o'clock, I assume is the Drain. When positioned at 12 and 6, I figured...
Top