• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by Sandhills-elect

  1. S

    922b clutch pressure problems

    I know this is a very late reply, just never done anything to it, It worked as is never had time and never ran long periods so was OK. I did finally put some Lucas trans, conditioner in it. It seem to have fixed the problem. I think it was an o-ring in the selector because you could shift in...
  2. S

    922b clutch pressure problems

    thanks for the reply, i have some TO-4 oil to put in it, i was going to add it when i done the pump change. I think i am going to do some hose changing and try to find any check valves or springs that maybe week or need attention before i do the pump. I have a parts book just need to do a...
  3. S

    922b clutch pressure problems

    I check it right after i changed the oil and it was right on the full mark maybe even just a tad over, i have never checked it when the pressure dropped though, i only did it after i ran it and let it set for a bit at idel and it always checked fine. Thanks Brent.
  4. S

    922b clutch pressure problems

    I have owned it 4-5 months it did not do it at first, but did not run for long period of time at first. I am sure oil level is right because i added 8 gallon per manual requirements and that seems to show full like it said to the dipstick, the dip stick looks to be factory, and not just any...
  5. S

    922b clutch pressure problems

    Is there a check up to the pump? I checked the screen when i replaced the oil and had nothing in it, i did look it over the other day and it looks like someone has already done the pump, it is not cat yellow like the hydrualic pump, not saying it might not be bad. I am starting to think maybe...
  6. S

    922b clutch pressure problems

    I will update all when i have chance to get the new pump in, i have it, but a little on the cold side here right now, and i don't have a heated shop to do it in. If i needed right a this time i would get it done, but since i don't i am waiting for a warmer day, Thanks and stay tuned. Brent
  7. S

    922b clutch pressure problems

    That maybe be, i do recall that i would fall down sometimes to a 100-150 then come back up, i was not just staring at the gauge because i was using it so could not watch it all the time, the trans works very well lots of power until the pressure falls off, and you don't notice it until it is...
  8. S

    922b clutch pressure problems

    I checked it out and it is spec out to cat TO-2 so i think i will be alright. Sorry for asking what To-4 was i found out it is cat oil number. Thanks again for all the help! Brent.
  9. S

    922b clutch pressure problems

    I am using 15-40 john Deere oil 50 plus, and it says it is a ci-4, i am really not sure what that means. What good name brand oil runs the TO-4? I am in the sticks here so it is a 75 mile drive to a town of more than 200 people. Thanks Brent.
  10. S

    922b clutch pressure problems

    i can do that, maybe a week or two before i get it done, i am not using it any more for a while. Brent.
  11. S

    922b clutch pressure problems

    Thanks so much for the info!! that is kind of where i was leaning. Brent
  12. S

    922b clutch pressure problems

    I am thinking weak spring in control valve, or bad transmission pump. Brent.
  13. S

    922b clutch pressure problems

    in the book it calls for straight 30wt, if it is below 32F you dilute with kerosene, so i just used a multi viscosity that they did not have in 1964. Brent.
  14. S

    922b clutch pressure problems

    Hello, i have a cat 922b with clutch pressure problems, it will start out at 250 psi, use it a while no set time, and then all of a sudden will loose pressure, i can shut it off and wait just a little bit and restart and it will come back to 250 again, but usually does not last as long as the...
  15. S

    1989 Prime-mover or John Deere LD50

    Thanks Justin, but i guess i am out of luck, i was looking at buying this loader but i was contacted friday, and he sold it. Thanks for the post and your time. Brent. PS. i was sure it was no JD444 but was wanting to make sure i could get parts.
See more
Top