John Deere 410 Engine Rebuild HELP

[sbarrett]

resized all 4 on my 310a, were not tongue and groove, but 410 might be different.

 

[Tinkerer]

Check for accuracy for your particular engine if you are interested in replacing the rods.



https://www.ebay.com/itm/172656781814?_trkparms=ispr=1&amdata=enc:AQAFAAACMBaobrjLl8XobRIiIML1V4Imu%2Fn%2BzU5L90Z278x5ickkKQ3D59%2FksmrAqH9M4NgB35b14DNPiwamiRWYcTF8yhIPlnw7TYj3zpVIcPxDb%2ByfJhS1PWzRH4kqSSpbxu8jjHnKNrMMkjOcqWMNSC%2Fo4p0GW%2FRXeRZVWOoZyje%2B7akH%2B6RSJv3jpbKqdU%2F3E%2BSQF1iEDoqw1vH5tU84a7gIXoMKLNsKi1xvlUMD7sozqu%2BquiQZhmoI46uOtFHG9SjAI%2FBoyaW%2BCu5Nj2uYh93vnTAu%2FEDZk4LZR3Qy%2F52vJQYy3GHxnnNnLl4mhFb1O23JZNX3IBsSvEPNDNLuqzRWG%2Bp9veDoXR1YfzoDFAz0x7f2AJDoQ2ZIbDdRtsCiX6sOcMg8Yl3U6N51ZDQBTKueKkaaJIJUloeyDRgJLQeGAw4XAlzYHGxRSzoFHv6D7oBsxPSCmdyCQDsnbzKOP8UPsjVK7J%2FpV4Z0Rvt1hOAL8Fk0U7lJHlHr1loFL72HurqfUx4pULIxTVHG%2F4MOUqsHPAYMAcDm%2FZJTDerWfDsoCy71jktjbMyLSgmBWnnL6K0ewJgMsqdpb08HVMw%2Fi5tRRuzqbSCrthvoDfdGplSGNeMWLXWFO2orBLwIlblAV5Vg6z4aPcRG4lKbspIUaRraG8DHDAesjbf1YziqwGNrf%2FqZVzPsLWt3KxOxIH0zfPxIEtWPMLVb6bGbGHeucWHHuJ2dIbPtSWPUMZbepiE%2BiNVJ|cksum:1726567818145309ffabda3746a68d0db83a49079770|ampidL_CLK|clp:3268220&chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=172656781814&targetid=1098102009964&device=c&mktype=pla&googleloc=9021977&poi=&campaignid=11774045932&mkgroupid=117378450867&rlsatarget=pla-1098102009964&abcId=9300473&merchantid=113776401&gclid=Cj0KCQiA_qD_BRDiARIsANjZ2LC2b1ifrSP9dFa29iuQW8RDZKo638UXcRRo5UUYeLamUEqnl2_u-GQaAiyQEALw_wcB

 

[Burns-Tractors]

Thanks for all the replies, sorry I didn't see them sooner, some reason I didn't get any email updates???

It was a rod bearing that went out, it ruined the one connecting rod but all the other bearings look OK. Do you think I need to replace all the connecting rods? I was just going to replace the one. What's the best way to measure them for wear? I am not wanting to do this again anytime soon so I want to do it right the first time!
Thanks again for the help!

 

[Tinkerer]

Thanks for all the replies, sorry I didn't see them sooner, some reason I didn't get any email updates???
Thanks again for the help!

You already have to buy one new one. Why not just buy all four. Cheap insurance I think.
IMHO !
In regards to not get notified when someone replies to your thread. Did check the box that enables notifications ?
At the top of the page it says WATCH THREAD. You have to click on it and then you will get a pop-up like this. ---->