• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. J

    JLG / Scissor lift form/repair help

    You won’t be able to get individual diodes or transistors from jlg for the board, would have to get the whole board assembly. The board looks damaged too anyway.
  2. J

    JLG / Scissor lift form/repair help

    My bad thought you wrote 2030es, either way their site has the manuals for them all.
  3. J

    JLG / Scissor lift form/repair help

    Go to jlg.s website and you can download the service manuals for them. As far as the controller, it depends on what the serial number is the older ones had a ckt board in the ground control box that held all the programming, the newer ones that was integrated into the motor controller. The...
  4. J

    Genie TMZ-50/30 Man lift with no power

    You’d need to loosen the holding valves too.
  5. J

    JLG 400S manlift

    That serial should means the lift should have ADE system, you could check the function speeds with a jlg handset if you have one, if it’s pre-ADE, then the joysticks themselves have cards that can be adjusted for the speeds. How does he know the oil is heating up too much? Travel and swing...
  6. J

    Simple Deutz 2011 oil change?

    There’s also a screen under the cap of the lift pump. Take the two torch or philips screws (can’t remember which they are) off the pull the cover. The screen is under that.
  7. J

    Genie TMZ-50/30 Man lift with no power

    Could be as simple as the coils put on wrong or connected to the wrong wiring. Up wiring connected to down, and down connected to up.
  8. J

    JLG lifts

    If you’re going to repair them yourself get a jlg handset they’re $250 and a must have tool for diagnostics and calibrating the machines.
  9. J

    Valve adjustment

    It would tighten cause of the expansion due to heat.
  10. J

    Genie TMZ-50/30 Man lift with no power

    Usually all genies need to see both e-stops on the power up, no matter which controls your going to use. Really need the service manual cause depending on what the serial number is the wiring can be different. Looks like most of them the key switch is fed power from the ground e-stop...
  11. J

    Genie TMZ-50/30 Man lift with no power

    Go to genie website and download the service manual for it. Make sure you have power in and out of the key switch, and both e-stops.
  12. J

    Skyjack wheels turn but won’t drive or lift

    I had that happen on one where I was given the wrong joystick to install. With the wrong one on only steer worked. The correct joystick and the wrong one looked exactly the same just a different part number. Not saying that is your issue but may be worth checking into.
  13. J

    genie GS 5390 shutoff solenoid.

    You don’t have to remove the metal plate, just that plastic piece you have the arrow pointing to, once you get that piece off, remove the solenoid and try and start it. If it starts and runs you know the solenoid is bad, only thing is it won’t shut off. To shut it off you have to stick your...
  14. J

    Manuals

    https://www.servicemanualbit.com/ I’ve used this place before. Needed a Nissan forklift manual at work and found this site. Usually pretty cheap to buy.
  15. J

    TH560B slow hydraulic function help.

    Do the hoses for the tilt have quick disconnects? I’ve seen them fail where one direction will flow then the other direction it’ll start to close the disconnect slowing the flow down or even stopping it.
  16. J

    JCB 530 - No Reverse

    https://www.servicemanualbit.com/ I found this website googling at work when I needed a manual for a Nissan forklift. Had my job buy them to make sure it wasn’t a scam. Purchased a few from this site so far and haven’t had any issues. We’re pretty cheap too.
  17. J

    What kind of Clark Forklift

    Not really, try and find parts for a Strato-lift scissor lift. Besides the pq joystick and generic relays/switches you won’t find any parts available. My job is mostly hyster and Yale forklifts and even some old hyster’s some parts are just not available anymore.
  18. J

    What kind of Clark Forklift

    But can you get parts, like say the hydraulic control valves were worn would parts even be available? I imagine it would be very hard to find parts on some of these old ones.
  19. J

    What kind of Clark Forklift

    Serious question, I’m not trying to be an a-hole but why would anyone buy such an old machine? Any piece of equipment that old.
  20. J

    Genie Z-45/25 drive pressure adjustment ???

    Why can’t you just do the normal brake test? Is this a company policy or something? Did you try pulling the coil off the brake valve but keep it connected, the brakes should be locked and it should try and drive to test them.
Top