• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. Hcnyl

    S45 wont steer

    The solenoid should be spring return center if I'm thinking correctly. strange.....:cool:
  2. Hcnyl

    Genie lift 45/22 DC Z boom lift

    You can remove the solenoids and put 12vdc (I'm assuming thats what they are) and see if they move spools. Don't take coil off valve and energize! It will ruin them. I have even used a screwdriver and put through the coil and energized it should pull on your screwdriver. Check dump valves also...
  3. Hcnyl

    Hydraulic Surging......... Stumped........ Model Genie S/N Z45004897

    On my list to check today.... thanks
  4. Hcnyl

    Hydraulic Surging......... Stumped........ Model Genie S/N Z45004897

    Update.... I put a guage between accumulator and check valve. When I start the lift it idles at about 300lbs. of pressure as it should. The oscillation valve switches and cylinders retract as they should (Untill the lift basket gets so far off the ground). I removed wiring from steering valve...
  5. Hcnyl

    Hydraulic Surging......... Stumped........ Model Genie S/N Z45004897

    I will put a guage in between accumulator and inlet and check that. Thanks, I'll let you know!!!:D:D:D
  6. Hcnyl

    Hydraulic Surging......... Stumped........ Model Genie S/N Z45004897

    See if this helps any.
  7. Hcnyl

    Hydraulic Surging......... Stumped........ Model Genie S/N Z45004897

    Do you have a number, the last guy I talked to said I need to find a local tech
  8. Hcnyl

    Hydraulic Surging......... Stumped........ Model Genie S/N Z45004897

    Ya, I have downloaded every Manual I can find, Nothing on my issue? I call Genie and all they want to do is sell me a different machine. I like (not right now) this one..... :Do_O;) thanks though. I'll keep diggin!!
  9. Hcnyl

    Hydraulic Surging......... Stumped........ Model Genie S/N Z45004897

    Ok, so I'll try and explain this as best I can.... Z45/22 running on Gas, Ford LGR423 when I start it up and let it Idle from the ground and let it warm up it idles well and then it runs up the pressure to around 1800 pounds and the relief on Steer OSC. manifold trips. It happens about every...
  10. Hcnyl

    Horsepower Limiter on Genie Z45/22

    Good morning, I have been restoring a 1996 Genie Z45/22. It has a LGR423 Ford 4 Cylinder for a motor and I removed the LP portion of wiring. I have everything working now except the drive function is kicking my ASS!!!! I have checked voltage to the card on terminaals #1 and #2 which is above...
  11. Hcnyl

    Genie Z45/22 Ignition Module

    Z45/22 It has a ford LGR425 4 cylinder in it. jlynchelectric@hotmail.com
  12. Hcnyl

    Genie Z45/22 Ignition Module

    Took wiring harness off Lift and found burnt wires. Repaired/Replaced wiring, It is firing on all 4 cylinders now. Starts and runs about 10 seconds and dies, thinking feedback from Alternator is missing and shutting gas off. Yes it has a carburetor. It is a Model Z45/22 1996 model Has a ford...
  13. Hcnyl

    Genie Z45/22 Ignition Module

    Yes, I called dvautoparts they didn't have anymore. I found a place that had a conversion kit at a cost of $1600.00. I have removed wiring harness and found some melted wires. It is firing on all cylinders now but will still not start. I have checked compression in cylinders and they are...
  14. Hcnyl

    Genie Z45/22 Ignition Module

    I have an older Model Genie S/N Z45004897 Has a Ford LRG-4231 motor with an obsolete Ignition Module. Does anyone know of a conversion or where I could purchase a module? It only fires on one side of the coil, I replaced the coil and get the same thing. I have tried plugs, wires, timing? Baffled...
Top