• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. F

    Yanmar Diagnostic Connector

    Hi all, Just wondering where the diagnostic connector is on the yanmar excavators? Thanks
  2. F

    Yanmar Fault code Help

    Hi Everyone, Just wondering what 28 000096.04 fault code relates too? I believe its something to do with the fuel level sensor or wiring. Any help appreciated. Machine is a Yanmar Vio 55-6B Machine. TIA
  3. F

    Yanmar VIO 55 Vibration.

    Hi All, Have a Yanmar VIO 55-6B with a vibration coming up through the cab when cold. After a while of operating it disappears. I did wonder if the drive coupling is starting to disintegrate but it doesn't make sense as to why it disappears. Machine has around 6000hrs on the clock. Could pump...
  4. F

    Yanmar Vio 1.7 Engine noise

    Hi Everyone, Have a little Yanmar 1.7t excavator that went over backwards so the tracks ended up pointing to the sky and the back of the ROPS frame laying on the ground. From what I've been told by the operator the engine probably run in this state at full revs for approx 30sec before being...
  5. F

    Hitachi ZX65 top roller failure.

    Hey Guys, Just wondering how many hours roughly you'd expect to get out of the top rollers on diggers around the 3t to 6t range. Have a Hitachi 65 that seems to go through a few, like only getting a year out of them. They are rubber tracks and tensioned to the specs in the operators manual...
  6. F

    Hitachi LX80 Loader

    Hi, Does anyone have a diagram or manual of how the brakes work on these loaders? Have one that the pedal just goes to the floor, Brake reservoir is empty and it doesn't look like brake fluid when your bleed system. Not familiar with these systems. Was wondering if seals inside are shot...
  7. F

    Volvo EC220DL Maintenance

    Hi, Have a Volvo EC220DL Excavator. In the manual it says to check the slew gear grease level. to check it you take small diamond shape cover off under the right hand side steps and inspect level. my question is where is the level supposed to be? There is about 10mm of grease on the base of...
  8. F

    Kubota M105X Transmission Calibration

    Hi, Just wondering if anyone has the Calibration procedure for the transmission on a Kubota M105X? Thanks In Advance
  9. F

    Komatsu WA80 Loader manual

    Hi, does anybody have a manual for the front axle on a Komatsu wa80-3 loader? The drive shaft let go and now can’t get the input shaft to stop leaking, have replaced seal but still no good. Also what the process to bleed brakes? Thanks
  10. F

    Yanmar Vio55-6 running rough

    Hey, Have a Yanmar Vio55-6 that shows fault code 00 000110.03 and engine runs rough every now and then. Have found if I disconnect the plug that goes to the cold start function (told by dealer) on the injector pump the problem goes away and runs smoothly but brings up fault code 00 522242.04...
  11. F

    Hitachi ZX130LCN-5B Alternator Belt

    Hi All, I need to replace the alternator belt on a Hitachi ZX130LCN-5B. Question is do you have to remove the fan to replace the belt because the belt is to small to slip over the fan blades. If so what size are the bolt heads as you can't see down there? Thanks in advance
  12. F

    Ditch Witch RT80 Dash Display Fault

    Hi All, Hoping some one might be able to point me in the right direction. A ditch witch RT80 dash display has a fault where when yo turn the key on it displays "Booting" then the ditch witch logo then goes blank. There is no gauges displayed. Any ideas would be much appreciated. Thanks
  13. F

    Bobcat S160 oil in the header tank

    Have a customers Bobcat S160 that has oil in the header tank. I have never worked on one of these machines before so unsure if it is in fact engine oil and not hydraulic oil in the tank. From what I have read common cause is a blown head gasket or cracked/Warped head due to over heating. They...
  14. F

    Ditch Witch RT80 info

    Hi everyone, I have been recently doing some work on a ditch witch RT80 Quad. Just wondering if there is any technical info on this machine as the dealer here is about as much use as a fly screen door on a submarine. We have the operators manual but that gives limited information. Any help would...
  15. F

    Yanmar SV100 Hydraulic Valve block leak

    Hi Everyone, I'm new to this forum so apologies if this is in the wrong thread. I am working on a Yanmar sv100 which has developed a leak on the main valve block under the floor of the cab. Where it's most wet is the last one closest to the centre of the machine. I'm thinking its the o-rings in...
Top