-
Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!
Search results
-
K
700H trouble code
Finally got back down to dozer. As far as looks, sensor I installed last year looks completely different than the originals. I swapped Decel and steer sensor and Calibration passed. I continued with calibration and failed on high speed. showed code for left motor PCP. Last number 8 and no other... -
K
700H trouble code
I just looked at the number and it shows that potentiameter to be used in several spots on this machine. I will try to swap the sensor with another one and see if I get a different fault code. -
K
700H trouble code
I don't remember. It is a piher. The customer ordered It and picked it up. It was there when I got there last year. -
K
700H trouble code
Finally got back down to machine and went through the diag. procedure per op and test. Results Voltage Low2.22 Voltage High2.68 Manual page 606 voltage appears to be a little high at WOT. Voltage difference is a little low. Voltage from TCM was in spec. Wires ohmed out good from B1... -
K
700H trouble code
I saw this and will have to fabricate a test harness. I will make one and update when I have more information. Thanks -
K
700H trouble code
I have a customer with a 700H S#915091. This dozer sits in the middle of a ranch and rats have done some major damage. I removed harness and repaired it and reinstalled. Now I am showing a F358(B1 Decel Sensor) I checked voltage in TCU to find 1900mv at idle and 2700mv at WOT. The kicker is if I... -
K
JD 700H Transmission controller
There are a few rebuilders online. Use the part number in the search bar to find them. -
K
2000 650h lgp
I'm still getting to the forward low section of the calibration can I get the 4 failed codes for both pumps. At this point I am wondering if this is more of a computer issue. -
K
2000 650h lgp
My email is krauseb24@gmail.com. I double checked and null and pcp adjustment. Everything seemed right. In the DIAG screen both the pumps show 0 millivolts all other functions show values. These were measurments taken at wide open throttle. On the left pump millivolts Speed 2 and forward was... -
K
2000 650h lgp
Checked fspd and rspd and set them to med. I adjusted the motors to 3400 rpm. I tryed calibration and it failed with a f3a7. I tryed it again and it went through the low track spd part and the tcu said save and froze. I pushed and held all the buttons but nothing changed. I cut the key and... -
K
2000 650h lgp
Both my motor speeds we're about 1800 RPM with the pump fully stroked and in Speed 3 the codes I got the first 3 attempts at a calibration are F3D7, F3E7, F3N1, F3M1. I got these before I got to the track speed part. The last part I got F3C8 and F3D8. I increased motor speeds to 2300 RPM... -
K
2000 650h lgp
Also I'm getting a list of codes during calibration that seemed to disappear the more times I attempt it. Is this normal? -
K
2000 650h lgp
Okay got back to the Dozer. Check the PCP and they were all in spec. Now during the motor adjustment the manual gives 2 specs. Both say to use a test harness that will supply 5 volts to the PCP. My question is do I ignore the lower-spec and go with the Higher One with Speed 3 and wide open... -
K
2000 650h lgp
I'm pulling my hair out over this. Us there any tests I can perform to help narrow this issue or something I can check? -
K
2000 650h lgp
Alright guys here's the story. A friend of mine asked me to work on his bulldozer and I agreed. I am a tractor mechanic and have never work on a bulldozer before. So we bought the service manual and the operation and test manual. He felt a pretty bad vibration and heard a loud pop. He knows when...