• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. Mpat70

    Allis Chalmers D14 service & parts manual

    I will do that thanks
  2. Mpat70

    Allis Chalmers D14 service & parts manual

    Great idea with the ball valve. So when I tighten or loosen the control valve I should see a difference in my boom, but I don't see any difference. Could this help narrow it down?
  3. Mpat70

    Case 580b blue smoke

    I had a connecting rod come out in my Allis Chalmers D14 the day after I purchased it in 2015, I did a complete inframe overhaul on it. It was my very first experience with overhauling anything. Since then I have overhauled my Massey 135, little Iseki tx1500 4x4 with garden tiller, 95 Ford f150...
  4. Mpat70

    Case 580b blue smoke

    Solid advice, I just need to head over to utube to watch some videos to figure out how to do a compression test but; I'm very observant and learn by watching so I will get it done. Thanks again Tinkerer for sharing your vast well if knowledge to us greenhorns!!!
  5. Mpat70

    Allis Chalmers D14 service & parts manual

    Ok great. I will start with that. Thank you!
  6. Mpat70

    Allis Chalmers D14 service & parts manual

    Boom control seals? What are these? I've repacked the boom cylinder, are you talking about the hydraulic lever? I checked the spring on both sides of the control lever and the appeared fine. Could this thing in the pic below be the problem? It some type of pressure valve. I took it apart and no...
  7. Mpat70

    Allis Chalmers D14 service & parts manual

    In addition it's has a Parsons "Shawnee" backhoe, factory installed, and the boom drifts down even with a new cylinder. Once it heats up it had no lifting power ! Any suggestions where to look and what I'm looking for?
  8. Mpat70

    Allis Chalmers D14 service & parts manual

    Does anyone have a link to the manuals for a D14? I'm needing to figure out how to rebuild my power steering or do I just need to replace a seal. It works just fine but it's leaking fluid. Links to free PDF would be great!
  9. Mpat70

    Case 580b blue smoke

    Thanks for the advice Edge, I will take it into consideration!
  10. Mpat70

    Case 580b blue smoke

    I am going tomorrow to Napa for a shaft oil seal. My right brake drum is leaking 90wt.
  11. Mpat70

    Case 580b blue smoke

    No sir I did not check compression. Thanks for the advice, I have already resigned myself to running it like this until it get worse. I will keep an eye on my oil level and dig!
  12. Mpat70

    Case 580B - Shifting from neutral into a gear

    Thanks Tink I will try this. Has you dog ever started looking like your food?
  13. Mpat70

    Case 580B - Shifting from neutral into a gear

    1. I hooked up two wires to the button. I took the two wires and touched them to the starter ground and power. Nothing happened. I pressed starter button and the engine turned over. So button is good. 2. Where is the neutral safety switch? 3. Wire between switch and starter button is good. 4...
  14. Mpat70

    Case 580B - Shifting from neutral into a gear

    Ok now I got another yet another issue. I was bumping my start button to rotate the flywheel looking for tdc marks. Anyway, my button stopped working. I wired the button directly to the started and it worked fine. I'm not getting any juice my key switch? Is there a fuse I might have blown?
  15. Mpat70

    Case 580B - Shifting from neutral into a gear

    Anybody looking for a 350 engine
  16. Mpat70

    Case 580B - Shifting from neutral into a gear

    Thanks for the info
  17. Mpat70

    Case 580B - Shifting from neutral into a gear

    Ok gotcha. Yes I have pressure washed the entire thing including underneath. I don't think it had ever been washed before. There was inches of grime building in some areas and joints were completely clogged. Thanks for the info.
  18. Mpat70

    Case 580B - Shifting from neutral into a gear

    Thanks for the illustration. Do I'm guessing that "freeing up some components" is the same as adjusting the linkage?
  19. Mpat70

    Case 580B - Shifting from neutral into a gear

    We do you mean about freeing up some components?
  20. Mpat70

    Case 580b blue smoke

    I will try advancing the timing. Thanks for the tip!
Top