-
Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!
Search results
-
-
-
555E Wheel bearing preload torque spec
Is there a specification in the manual for hub pre-load or allowable end play? I don't see a provision for adjusting it in the picture you posted if its too tight or loose. Proper adjustment is very important.- mekanik
- Post #15
- Forum: Tractor/Loader/Backhoes
-
Memories for us old truckers
The 1710 I had to work on them. What a horrible engine!!! -
wheel nuts
You can take them to the grinder and carefully remove the outer "skin".- mekanik
- Post #13
- Forum: General Industry Questions
-
-
Dump truck box won't come down
Is there a machine there that could set something heavy in the box? -
Trying to get a l10 Pete 377 running.
That 2 wire harness could be the data link. Early Celect engines used Cummins's ECAP suitcase to communicate with the engine. It had a 2 wire metripack data connector and a power plug that fit a cigarette lighter. -
I have a 2016 Bobcat E26 bleeding hydraulic system
Can you post a picture of the connector?- mekanik
- Post #2
- Forum: Excavators
-
-
ISX oil leak
The gasket between the block and front cover is steel with a Viton? rubber like sealing bead bonded to the areas that seal. If I remember correctly there is a passage in the front cover that connects the oil drillings on both sides of the block. The seal deteriorates over time and leaks when... -
1967 C180 cummins need a set of fuel rails
I have worked on Cummins engines that had the flanged injectors but I don't recall how the lines connected to the injectors, compression fittings? Could you make lines up from 1/4" and 3/16" brake line and fittings? -
Wire Connectors
Something like this might be able to get into where you need. https://www.amazon.com/OTC-5950A-Crimpro-Angled-Service/dp/B00CDDBAQU- mekanik
- Post #3
- Forum: Excavators
-
Strange buyer's
Banks have to be careful of fraud too. A Notary Public pulled off a substantial bank fraud was never caught and the way he did it is still wide open for exploitation. Here is an explanation of what a Notary is as they may called something different south of the border: A notary public (a.k.a...- mekanik
- Post #153
- Forum: General Industry Questions
-
Navistar Engineering
I had an International Work-Star with a Maxxfarce 10 in the shop yesterday. The complaint was after driving for a few minutes the check engine light would come on. I scanned it and it had two faults for injection pressure above desired and below desired pressure. My best guess is either the... -
Strange buyer's
When my siblings and I cleaned out my parents house I was shocked at how much garbage my Dad saved. We had a two yard dumpster dropped at the house and we filled it twice. My Dad never got rid of anything. I promised myself I would not do that to my children. I have spent the past couple years...- mekanik
- Post #51
- Forum: General Industry Questions
-
Memories for us old truckers
I thought it might be. I searched the internet and could not find one that looked like it. -
Strange buyer's
A friend tells me its the same way on the dating sites.- mekanik
- Post #12
- Forum: General Industry Questions
-
2007 International 4300 Durastar no power on freeway
The orifice in the filter housing takes a 7mm allen wrench to remove it. The grit in the bottom of the housing will go through the orifice into the fuel inlet and through the strainer and then through the transfer pump and back into the filter housing going around continuously until enough... -