• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. B

    bucket tooth

    what is the part # or size i need
  2. B

    580 k gear grind ?

    580k phase 1 getting a gear grind when i let off power and brake sounds like when you shift a manual tranny and miss the gear a bit grrrr/pop . comes from right under the floor it only lasts a half second it happens in any gear forward and reverse most...
  3. B

    another flat

    no hole in the sidewall no hole anywhere but tube is trashed cause i drove on it to long flat and ripped the valve stem looks more like a tear about three inches up from the rim edge oh well
  4. B

    580k shuttle ouyput shaft seal

    ok so i got the output seal dripping some can i get the seal out by prying it out with just the yoke off or do ineed put that tail off too with the six bolts and do the paper gasket and do i need to drain all oil or just let it spill out during repair and top off later seal...
  5. B

    tire damage

    hit a pipe of some kind repairable and how? 17.5l-24 r4 its got a inner tube what size inner tube or type im new at this tips advice .......
  6. B

    weld on ductile??

    ok so i have a manual thumb on my ductile stick it keeps on shifting upward then i cant line up the hole on the bracket . how can i fix it from moving i got the nuts down tight even broke two wrenches in the process the botom bracket slides about 3/4 over to the left . i got i back...
  7. B

    bouncy boom 580k

    i just noticed when i unlock the boom and tip it out a bit it does this bouncy back and forth a few times before it holds spongy like seals or the rod nut ?
  8. B

    580k cav inj pump?

    ok in this pic there a line on the top cover it goes to a tee ,the other line it meets is from the injectors then in goes into a short rubber line then into what i think is a check valve in the frame then .back in to the fuel tank. ok Question if i were to break open that fitting /...
  9. B

    580k door hinge right side 2 part window / door /frame

    ok so the door hinge pin was snapped on the top part of hinge door to frame part so the top door flops out but the same hinge bottom part holds the window mount and window functions properly the bottom hinge works ok i currently have the door screwed on by a plate to...
  10. B

    580k arm to coupler pivot bushing ?

    ok i thought the bushing was missing / but on closer inspections the one side has drifted in so far that it sits only in the coupler and not in the dipper arm / how far do they go in im guessing flush ? theres one on each side and if i peek inside they just about touching each other i...
  11. B

    bucket removal 580k

    so i need to put in a missing bushing on the dipper arm / and another missing bushing on the bucket itself / so is there a procedure to drop the bucket that most efficient / i got that part on the end that has the quick hook to pin ./or is it called a qui ck coupler so if im correct...
  12. B

    winter storage

    gonna leave my 580k outside for the winter . are there any things to do that are best for leaving out in the elements what do you do? stabilizers up or down / loader/ bucket/ ?? leave boom in travel position ??? use a cover ? lubricate exposed cyl rods?..air up the tires ? the...
  13. B

    580k dipper ??

    im getting a weird shudder or a machine gun like banging when i curl the bucket in , but not all the time . only when u go full out then full back in it starts a hyd thumping and the bucket stutters in the return speed also is bucket out speed faster than pulling in?
  14. B

    580 sloenoid spring

    ok where does it go ???
  15. B

    led upgrade

    90$ for one flood light screw that for 90 i got a set of led floods and replaced the taillights very kool but not after i found a pesky short141987
  16. B

    swing tower cam ?? off the roller

    is the roller too high or the cam too low
  17. B

    580 k glands repair but...

    ok i did the stabilizers yesterday and the swings today but i now notice one stab/ leaking from the edge where the tube and cap meet . did i do a booboo with the oring . also its not a round std black oring but a green placticey type oring with a groove ? i hate to unscrew the pia again i did...
  18. B

    can move dipper bucket by hand

    i just noticed today with the machine parked . i can push n pull the dipper bucket back n forth a few inches i see the cyl rod going in n out with it too .. air inside ? glands ? control?
  19. B

    580k fuel solenoid

    whats up these things work ??it will start cold but ten minutes and warm engine and they suck mmy nuts bench test on 12v and they seem have a poor snap on the plunger what with this spring thing i heard about was no spring on the old one ?? none fell out . no room to fit...
  20. B

    window latch 580k p1

    Location: (580K) - LOADER BACKHOE (NORTH AMERICA) > (09-601[01]) - KIT LATCH WINDOW SIDE > KIT (Part#: B96584) will the repair my lever style window latch
Top