• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. CDNDIESELMONKEY

    Hesston 4910 electrical issues

    That makes sense. I guess why I thought they were welded in there is because the parts book calls it an arm assembly and the parts guy said they are welded in. I have the parts book on my laptop and will check later today
  2. CDNDIESELMONKEY

    Hesston 4910 electrical issues

    So with opens between all four pins. Are those load bars faulty. Can they be cut open and the load bars alone replaced??
  3. CDNDIESELMONKEY

    Hesston 4910 electrical issues

    Good morning. I working on a friends hesston 4910 large square baler (serial number is HL00733). This baler puts up an error code of 7 or 6 and then doesn't read any hydraulic pressures on the monitor. I pinned out the harness and the harness has proper continuity and has no shorts. When I...
  4. CDNDIESELMONKEY

    D4-C Idler

    Usually just the failed side. Thanks.
  5. CDNDIESELMONKEY

    Hitachi ZX 160LC-3 Power Loss Under Load

    I've seen this before. There are what Hitachi calls overflow relief valves in the secondary fuel filter housing. It is not listed in service advisor but good parts guys can find them. The springs get weak and your fuel supply to your suction control valve does not provide enough fuel for you to...
  6. CDNDIESELMONKEY

    Front window replacement

    Good afternoon. I have a Hitachi ZX290LC-5N where the upper front window broke out of the machine. What do i have to do to get the window replaced. I only have the glass and have to travel 3 hours to site. Does it just unbolt from the bottom and slide out? Thanks for the help!!
  7. CDNDIESELMONKEY

    JCB 550/170 How to remove steering wheel

    Pop the plastic JCB cover off with a screwdriver. Use a 22mm or 24 mm and loosen the nut. Back it off till it's still on two threads. Get your very strong assistant in there and lift hard on both sides of the wheel at 9 and 3 o'clock.. they're tight but that's the way to get it off.
  8. CDNDIESELMONKEY

    1987 JCB 3CX (1550B) Loader Curl Cylinders not in synch

    I've had this a few times on JAN 3cx and 212 backhoe.
  9. CDNDIESELMONKEY

    1987 JCB 3CX (1550B) Loader Curl Cylinders not in synch

    I wouldn't worry about bleeding air. After you get it together it you can fully cycle the cylinders and that will bleed the air sufficiently. However keep in mind that some some of JCB British Standard Parallel Pipe fittings use o rings and you may have to change them after cracking the lines...
  10. CDNDIESELMONKEY

    1987 JCB 3CX (1550B) Loader Curl Cylinders not in synch

    Crack the lines and push the rod in by hand
  11. CDNDIESELMONKEY

    1998 Deere 590D excavator keeps burning up starters

    Make sure it is a 24volt starter. Some 12 volt starters will fit perfectly..
  12. CDNDIESELMONKEY

    Cat 336 safety shutoff

    Thanks for the responses! Yes we made one. Seemed too expensive for a piece that's just a marker. I used a bit of wood and some red heat shrink. Not perfect but it works.
  13. CDNDIESELMONKEY

    Cat 336 safety shutoff

    Good morning. We have several excavators missing the yellow hydraulic lock indicator lever. The dealer parts guys say that we have to order the whole valve. Does anyone know if just the yellow indicator is available? Thanks!
  14. CDNDIESELMONKEY

    What is this? Found in drain pail

    To make it even more of a head scratcher it also could of come out of a roadtech or Weller shuttle buggy!
  15. CDNDIESELMONKEY

    What is this? Found in drain pail

    Everything is working currently but I'm sure we'll find the failure soon enough!!
  16. CDNDIESELMONKEY

    What is this? Found in drain pail

    Hello everyone. I am working a fleet job. Mostly CAT, Volvo and some Hitachi and Deere. We have a big drum we use to drain all the engine, trans and hydraulic oils. Today I found this little metal part in the bottom. Does anyone know what this is? Thanks!
  17. CDNDIESELMONKEY

    1:50 scale construction model collection for sale

    Will you sell them separately?
  18. CDNDIESELMONKEY

    Allis Chalmers grader with electric brakes

    Did letourneau scrapers use Wagner electric brakes?
  19. CDNDIESELMONKEY

    Bunch of Pictures

    I just recently restarted reading on the forum site and first post was this one! Thanks for sharing! Seems like the Yukon would be very adventurous place to be a field service guy. I work in Toronto and spend most time in traffic. Lol. Do you ever run into tv people from gold rush?
  20. CDNDIESELMONKEY

    JCB JS160 problem, won't start

    Those are engine fault codes. Probably going to be hard to diagnose without service master software. Better get the dealership out. Of course check basic stuff first. No fuel in water, alternator charging etc
Top