• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. B

    Regulate thumb circuit flow jd590d

    I can see why you do it that way but you cannot see how inefficient your hydraulic motor actually is or how worn your pump is
  2. B

    Trencher

    Did you get this resolved
  3. B

    John Deere 310D backhoe

    I used to keep an extra cap on my service truck cause some of those old caps had like a brass mesh pressed in there..
  4. B

    Jd410g

    Condensation, and water will separate the glue on the clutch disk. Flush, flush,flush or you are going to be rebuilding the transmission
  5. B

    Regulate thumb circuit flow jd590d

    You are exactly correct it you will have to have flow meter hooked up to it to make sure your flow and pressures are correct. Before putting the attachment on.
  6. B

    overheating Hitachi

    Your breaker manufacturer will have a max return pressure spec And supply spec. I know for certain the Indeco breaker needs less than 105 psi. Measuring at the breaker. An Okada breaker can run up to 250 psi. I have set up more than 50 breakers on excavators Just using a good flow meter...
  7. B

    Excavator hydraulic operating pressure

    Your max normal operating pressure is 4980psi, but when you hit that boost button on top of the joystick (power digging) it gives you 5260 for 10-15 seconds. That is when stalling a function.
  8. B

    650G steering issue

    The brake band adjustment is separate from the clutch adjustment. It sounds like you are not fully declutching before braking. If memory is correct you will pull the brake lever aboout 2-3 inches and the clutch pressure will drop to 0 psi. Then 1-2 more inches and then you should have brake...
  9. B

    Hitachi Dr ZX

    so I did have the palm pilot version back in the day. and it had a software patch that also had to be run with it. to enable a specific pin out of the palm pilot that was not normally used.
  10. B

    Hitachi Dr ZX

    The original Dr. ZX software had to be ran on com ports 1,2,3 or 4. Make sure the drivers are installed for such software. However there is a lot of information you get out of the dash on a Deere C & D models. Without the cable. I do not know the Hitachi models of that era!
  11. B

    Hitachi Dr ZX

    I am not sure if the forum will let you put a screenshot of the software. I would be curious to see if it is the same as what I used. There have been so many names for that software. As the original Dr. ZX was handheld computer similar to what UPS uses on delivery trucks. But the original...
  12. B

    Hitachi Dr ZX

    with that software if memory is correct the diag cable is a USB adapter to serial to 4 pin. windows will automatically assign the USB port number but DR.ZX only runs on ports 1-4. so you may have to reasign it.
  13. B

    Hitachi EX120-2 hydraulic fluid?

    Make sure you bleed the pump before starting the engine. Use the large plug or fitting on top of the pump. Failure to do so could resuming then purchase of a new pump.
  14. B

    deere 544G locked up

    So usually when it gets unstuck like your talking about the problem then is usually the pedal pivot pin and not the valve. One does bolt to the other but. Crud usually gets under, behind, under the floor mat etc. blow it out. Lube only attracts the crud. However something to look at is the...
  15. B

    update on 762A

    Your saying like an articulation truck. 6x6.
  16. B

    update on 762A

    99 or 2000, I know this for sure cause the new owners bought our dealership and then bought a lot of scrapers. The last 862B’s off the line had turbo problems. And I remember our new owner coming to job site to see if I figured out the problem. We had 3 new scraper’s on job site with blown...
  17. B

    update on 762A

    When you say dump belly!! 1/2 of the floor moved back yes. And then the wall pushed forward so then only a couple of inches maybe all that was left on the floor.
  18. B

    update on 762A

    All I knew of Vermeer building was the last model. I work for Vermeer dealer now the last 10 yrs. in their museum in Pella, they have pictures of the deere scraper being built. But not many people there know the history. and why they quit. The hydraulic rear wheel assist was called the Max...
  19. B

    john deere 310D brake issue

    so i looked it up on the deere parts website. the part number is 15h562 for the pipe plug. yes it is on top rear of transaxle case. I do not remember if I used a mirror or just the right angle to view the adjustment bolt. Picture a 1/2 size bolt w/o flats and just a flat cut in it for large...
  20. B

    deere 544G locked up

    True, the more I think about it. The accumulator test was to, pump till the light came on then until brake’s were hard.
Top