• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by veikolaht

  1. V

    Perkins 1104D-E44TA

    To "absoluteyukon" - The engine turned around with a starter motor, just it did not start. So repairman mounted new turbo today (this was his decision) and of course the engine still did not start. Then I asked him to show me an old turbo and we found there some metal pieces of something - they...
  2. V

    Perkins 1104D-E44TA

    The engine stopped itself after about 10 sec strange low frequency sound/noise on full speed and will not start anymore. First time we tried to start it again right away, starter motor could not turn the engine, crankshaft was like blocked. Second time after about a minute engine turned around...
  3. V

    Perkins 1104D-E44TA

    Of course repairman will dismantle the turbo, just my opinion was he should do it immediately without waiting for new turbo, just in case, there can be something more broken than turbo only and from your answer I got confirmation about that. It is problem for as if we have to wait many days...
  4. V

    Perkins 1104D-E44TA

    So you think there is nothing between impeller in the exhaust side? And of course - what it could be :) Just I thought if there is something more than turbo which need to be changed - like you confirmed my opinion, that engine should start irrespective of turbo. I do not think there is some...
  5. V

    Perkins 1104D-E44TA

    Hi, we have a car baler with Perkins 1104D-E44TA engine. Few days ago an engine stopped almost on full speed and will not start anymore. Clear is, that Perkins turbo does not rotate, few mm only. I was thinking here, can be something (some broken part) from the cylinder is stacked between...
  6. V

    Perkins 1104D-E44TA

    Hi again! Is the turbo sound on this video OK? https://www.dropbox.com/s/7lifi13gtnforq0/turboUntitled.mp4?dl=0 The engine has ran 15-30 min. idle and this sound is in the beginning of pressing only, later disappears.
  7. V

    Perkins 1104D-E44TA

    Now is quite difficult to find some symptoms why baler did not work when cold because the temperature outside is +10°C or more and everything works fine. Piston pump should be in order. It gets hot when engine has ca 2200 rpm and no pressing but the processes there inside of the pump are extreme...
  8. V

    Perkins 1104D-E44TA

    This main hydraulic pump, piston pump PV080R1L1T1NWLC (information here http://www.hkhydraulic.com/pv080r1l1t1nwlc) gets in 5-10 minutes quite warm while the other three smaller pumps were cold. Started with cold engine and engine run on full gas, no pressing. Maybe it is normal. I have tested...
  9. V

    Perkins 1104D-E44TA

    Thank you, Brodiesel! How can it be overheating, when engine is cold? Should water pump work or not work irrespective of water/coolant temperature? But yes, ECM gave a fail code about coolant. After the problem started about 6 month ago we have changed injectors (without installing of trim...
  10. V

    Perkins 1104D-E44TA

    Hi! We have a car baler with Perkins engine - it is not earthmoving equipment, so if it is in wrong category, please, just lift it to the right. The problem is, that when we start pressing of cars, in the beginning, when engine and other things are cold, when hydraulic oil pumps will be...
  11. V

    Looking for a light weight long reach manlift

    Hi! I am new here and in some reason I cannot post new thread. Some sugestions? I get this: "...you do not have permission to access this page. This could be due to one of several reasons ..." And just for information - does somebody here knows about problems on the car baler "Colmar B5000"...
See more
Top