• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by HarryE

  1. H

    Huber-Warco 4D

    Looking for a clutch assembly any ideas?
  2. H

    Line Boreing

    Two of the pins are on a link that is no longer available. The machine shop will do the machine work on them, drill for grease ports and retainment bolts then send out for heat treat. I've heard of the Axle Surgeon but have no information on him.
  3. H

    Line Boreing

    Hello All, I am considering rebuilding the bucket on my 644b Deere loader. It needs the pin holes bored and bushed. Could anyone guestimate the cost for doing this? The bucket has other issues that can be over come but the pin holes are the biggest one. Also there was a forum member from Ohio...
  4. H

    2000 Volvo Fan Clutch w/Cummins ISM

    Fan clutch has not worked right since I bought truck 4 years ago. The radiator finally rotted out so since I had the room I thought I would remove the clutch to check it out. First stud on fan spun and when I applied air the seals were leaking so I bought a new clutch. But that wasn;t the...
  5. H

    644b Deere Loader Low Trans Pressure Question/Issue

    How long since filters were changed? What type transfluid are you using? And of course how is the level. My 644b @ idle shows little pressure but comes up at operating speed to I'm sure on my gage is 125#. It's 40 mi away so can't check it right now. A gallon low afects how mine operates. I have...
  6. H

    JD 5020 tools

    If your talking about the rear main seal. JD usually has a wear ring that is pressed on with the seal. There's a special tool that is required to do that and most dealers will loan the tool.
  7. H

    Your Lowboy Pictures Wanted

    1946 Trailmobile to haul my JD644b and other farm equipment. Previous owner replaced the spring axel's with a Neway air ride system. Some deck boards need replaced and I just picked up the steel for ramps.
  8. H

    JD 644B fix

    Purchased this loader knowing it had a issue with the top pivot pin. Just couldn't tell how bad it was until I could get it apart. The top pin had been run loose for quit some time and ob-longed the 1 1/2" top plate hole. The the lower 3/4" plate hole had been welded up in some fashion that did...
  9. H

    Hauling 10 ft equip on 8 ft trailer

    Not yet, Most of the trailers I've found are 8' w/out the out riggers. The one's with are priceier. Just lookig at the options.
  10. H

    Hauling 10 ft equip on 8 ft trailer

    I guess is a foot of tire over hang on each side w/ 23.5x25 acceptable? I'll be moving it 35 mi on state routes to the job.
  11. H

    Hauling 10 ft equip on 8 ft trailer

    With a 10 ft wide wheel loader how do you fellas do it? I was trying to figure out how you would tie it down if the trailer had ext it would make it difficult to reach the D rings with the chains. I'm just looking around to see what is best. Many years ago I hauled wide ag equipment up to 15'...
  12. H

    Terex 72-31B

    Hello All, I have been asked by a company to maintain their stone lot and remove snow. I went and looked at this machine yesterday. http://akroncanton.craigslist.org/bfs/4132897967.html Prior to their request I had been thinking of getting a D5 class dozer to clear fence rows around my...
See more
Top