• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by deereresurrector

  1. D

    I need help!

    Pump solenoid has 23.7 volts to it ,but when you disconnect it a plug it in there is no audible click .if I hook it up to straight battery voltage it clicks. Or does a controller pulsate the small valve in the insert
  2. D

    I need help!

    So what do torque controllers look like. I am not going to mess with them unless the rest of the KISS system is used up. If bit comes down to it what should I be looking for. I am certified in hyd system 17 years. Just the normal scoring and imbedded metal fragments. Or?
  3. D

    I need help!

    No I tossed them.pumps where surpost to been rebuilt,but that doesn't mean anything. 3 months ago. It did have tractor snot in and on filters and oil. We have ball chafing humidity out here and a bacteria came grow between hyd. Oil and water line if in system due to condensation
  4. D

    I need help!

    Where is torque controller on pump? Someone removed the pumps previous to me inheriting.the dumpling. Where is the torque controller.?most importantly what do I look for. I did change out the solenoid on pump. How tight is the valve insert that goes in before the solenoid to be torqued and the...
  5. D

    I need help!

    Return filters on hydraulic system? The two in the hyd res. Have been changed brand new .now where would the return filter be?
  6. D

    I need help!

    Black smoke bellows out during stall. So as far as air restriction the intake pipe isn't losing its shape and turbo charger turbine is not sloppy. Educate me please
  7. D

    I need help!

    what component has this #/ What is a torque back up and how do I check or set it properly? This unit is about an hour away from me so I'm trying to get a days worth of checks and diagnostics before I return to location.
  8. D

    I need help!

    The ycu 1127 sk300lc mark iv seems to be a rare model ,but by serial # the engine is correct to my knowledge
  9. D

    I need help!

    Ok pump guythe model # is CB.3-C cummins engine Family group xcexld505aba ,OD/L 505/8.3 , CPL 1845 , Serial # of engine 45821671, The injection pump is a Bosch tag on back of inj. pump is 96224 CDC ,0 402 066 702 AA , bar code on tag is 3933341 0100, plate on the side of injection pump is...
  10. D

    I need help!

    I do know there is a bit of farm yard engineering on fuel shut off solenoid . I wired back in solenoid so they dont have to pull a cable to get it started . Without a doubt that crap wasn't OEM.
  11. D

    I need help!

    I will retrieve injection pump # as well as engine codes on serial # plate Thank you.
  12. D

    I need help!

    So there is a strainer in the tank?! I have went through lines leaving primer pump and disconnected and resealed all connections. So also on inlet on primer pump has a screen? On a banjo fitting. I have not checked that yet and haven't checked strainer in tank.
  13. D

    I need help!

    It has the in line 6 cummins ycu 1127
  14. D

    I need help!

    It
  15. D

    I need help!

    OK this is what else I have done complete engine service, and hyd service. This one has the cummins engine. So all filters changed . On primer pump is screen on in ley or outlet. It was ca weird looking primer. not sure if its oem. no I didn't check it. Runs like a spotted ape with no load. but...
See more
Top