• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by crbearden

  1. C

    John Deere 4020 surges

    I hate to jump in here on an old thread. I have rebuilt a few of these pumps, or I should say I resealed them with a seal kit. I have installed the governor ring for the stationary engines in the ones I have rebuilt. It doesn't have the rubber to deteriorate and I have found that tractors are...
  2. C

    No power and water in transmission D6D

    Possible, the head was re done just before it was delivered. It did not seem to be missing, just no power. I haven't removed the hood to really get a good look. There is a lot of smoke coming from the turbo and manifold. I think the turbo housing is cracked into the oil gallery. The water...
  3. C

    No power and water in transmission D6D

    When it rains it pours. I had to dig a hole this afternoon and all that was available was the D6. I had it running a while ago and it was fine. We have had an ice storm and 12 inches of snow since. Taday it started fine, then when I went to push it just seemed to lose power. when I dropped the...
  4. C

    4-53 detroit rattles on deceleration

    I have a 4-53 detroit powering an Ingersoll Vane type compressor. When the pump is up to pressure and the engine decelerates a loud clicking noise is apparrent. Sometimes this noise continues at idle, and then is intermittent. The noise is not heard when the engine is loaded however. I am...
  5. C

    8.25 x 15 trailer wheel needed Demountable rim, 6515LWDE

    I have heard the stories of the old split rims, and I have mounted more of them than I can count.... I was taught by my Dad how to mount them and air them up and st and out of the way of flying parts. I am near OKC so I will check. this trailer is an old oil patch semi trailer that was made...
  6. C

    8.25 x 15 trailer wheel needed Demountable rim, 6515LWDE

    Looking for the 3 piece with the locking ring. There was one made that was only 2 pieces, but in over 50 years of experience I have only mounted 2 of those 2 peice rims and had no problems at that time....
  7. C

    8.25 x 15 trailer wheel needed Demountable rim, 6515LWDE

    In need of 1 or more 6.5 x 15 Dayton Wheels. Technical description is 15 x 6.5 Tube type demountable rim. I don't have a spare for my trailer and I have one wheel that it really bent up at the rim edge. The rim should have a 6515LWDE or LWD number on it. It is the type with the Lock Ring...
    • crbearden
    • Thread
    • 8.25 x 15 demountable rim low boy low platform trailer
    • Replies: 4
    • Forum: Trailers
  8. C

    Champion Grader

    I recently bought a 700 Champion with a 6cyl detroit. Only has 1500 hours. It was used for mixing asphalt for a small state highway department district. They went to contractor supplied asphalt and idled the grader. Every hydraulic cylinder needs rebuilding, but it runs and operates great...
  9. C

    Whats the worst large dozer?

    I would have to defend the Belarus Farm tractors. I have 2 of them, both bought used. A 96 model 825 and a 02 model 8345. They are 85 hp with 4wd, loaders and cabs made in Sweden. Only complaint I have is the A/c and heaters. They were added in Milwaukee WI. 8345 has a conventional...
See more
Top