• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by 5111

  1. 5

    ROBEX 80CR-9A problem and manuals

    Hello, Can someone share the service and operating manuals with schematics (electric and hydraulic) for the ROBEX 80CR-9A? The machine has power issues and the engine shuts down. After that it starts for a second, but it also has a low-speed cranking problem.
    • 5111
    • Thread
    • 80cr-9a robex 80cr-9a
    • Replies: 0
    • Forum: Excavators
  2. 5

    Case CX130B engine problem, manuals, schematics

  3. 5

    Case CX130B engine problem, manuals, schematics

    Checked the excavator today and found that the engine is running on only two cylinders. Started the engine and loosened the injector connections one by one: The 1st cylinder had power all the time. The 2nd cylinder had no power, but gained power when the 4th cylinder lost power. The 3rd...
  4. 5

    Case CX130B engine problem, manuals, schematics

    Hello, Does anybody have CASE CX130B (manufactured in 2008) manuals, schematics, or diagrams to share? The customer ordered a new Isuzu 4JJ1 engine with the wiring harness and fuel system, also new priming pump installe before engine change. After installation, the engine starts up well and...
    • 5111
    • Thread
    • 4jj1 case cx130b cx130b
    • Replies: 2
    • Forum: Excavators
  5. 5

    Atlas 1004

    I can check this belt when i'm near to machine.
  6. 5

    Nissan 1N1L180 fault codes

    Hello Need help to solve faultcodes D-FET OPEN 409 and P-FET OPEN 413. Machine sn is 1N1E722744 (2007) Tanks for your feedback.
  7. 5

    Atlas 1004

    Hi Does anybody can share 1993 Atlas 1004 excavator schematics of hydraulic and electric?
    • 5111
    • Thread
    • atlas 1004 diagrams
    • Replies: 7
    • Forum: Excavators
  8. 5

    JCB JS130 power dropping under load

    The JCB JS130 with serial number 2134576 is experiencing power loss under load conditions. The issue is not constant but it can show up when the operator is working the machine under higher load. I suspect it could be related to the fuel supply. Operator has been replaced the fuel supply pump...
    • 5111
    • Thread
    • jcb js130 power loss
    • Replies: 0
    • Forum: Excavators
  9. 5

    D6K2 Blade speed and calibration

    Hi Code was 104E - During calibration, the Implement ECM could not obtain a valid, constant baseline pressure needed to complete the calibration because pump discharge pressure varied too much. · Measure current to the solenoid or solenoids indicated in the calibration. The solenoid...
  10. 5

    D6K2 Blade speed and calibration

    Yes, but at the moment I don’t have any updates available for this software. The first time I performed the calibration using the visual method, and the second time I used the pressure-based method. After calibration, the blade movement became smoother—both at the start of motion and at...
  11. 5

    D6K2 Blade speed and calibration

    Thanks for the quick feedback, Nige. If I remember correctly, I can say that the machine has a lift cylinder without sensors, and the tilt cylinder sensor installation needs to be checked – but I think it’s also not installed...i changed tilt cylinder hoses and dosent saw it there. I remember...
  12. 5

    D6K2 Blade speed and calibration

    PDF is in following google drive link https://drive.google.com/file/d/1VdSFZl4ojgaNjMAj1CLBj47AYj5Jszyu/view?usp=sharing
  13. 5

    D6K2 Blade speed and calibration

    Hi, Does anybody have a idea what can be a problem in 2017 CAT D6K2 (sn JTR). Problem Description: During blade solenoid valve calibration pressure based (lift, angle, tilt) then it FAILS holding the joystick in the end position (for the function currently being calibrated), the blade does...
    • 5111
    • Thread
    • blade calibration d6k2
    • Replies: 10
    • Forum: Dozers
  14. 5

    D6N torque converter no power

    My mistake, the correct title should be Torque Converter
  15. 5

    D6N torque converter no power

    The scavenge screens are clean. The shaft stops rotating in all gears at low RPM when the service brake is applied. At high RPM, the shaft starts rotating in 1.5F and 1.5R gears, and the machine attempts to move, transferring power through the brakes to the final drives. The customer says that...
See more
Top