• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. O

    asv,rc85 paint

    Does anyone have the paint code,or asv part# for the 2005 yellow, on the RC85.Im wanting to do some touchup without a complete repaint.
  2. O

    D5C turbo issue (oil)

    UPDATE! Problem solved.Today I pulled the oil in,and oil out,lines from the turbo,both clean and no obstruction.By the way the banjo bolt on the oil in,is orficed to control volume.Put a hose on the return fitting in the block,clear as well.Started it,to warm up.Was going to pull the hose from...
  3. O

    D5C turbo issue (oil)

    My observation was at the front oil fill on the tap pet cover,when I said no detectable blow by, there is a slight pulse,but no more coming out than going in.Right now I'm leaning towards the return circuit.
  4. O

    D5C turbo issue (oil)

    Talked with the turbo guy today,He asked about the possibility of "upstream" oil entering the turbo from inlet side.There is no crankcase breather or other source of oil other than the oil feed 70psi going to the turbo.The crankcase vents out of the valve cover at the rear of the engine goes...
  5. O

    D5C turbo issue (oil)

    My D5C started using oil about fifty hours after engine rebuild.About a quart an hour under hard use.Oil pressure is 70/75 engine has no blow by and runs perfect.Pulled the turbo and found oil in the compressor side,took it to the shop for a rebuild($500) still going through oil.Today I serviced...
  6. O

    Samsung 120-2 No steering,transmission,hydraulics

    Just a couple thoughts,why did the shaft break?It was not twisted,the metal looked like it had crystallized. I knew I had seen that type of break before,but dammed if could remember.So I did the right thing,had one last Tullamore dew and went to bed.Fast forward 2AM woke up from a sound sleep...
  7. O

    Samsung 120-2 No steering,transmission,hydraulics

    You were correct #21 broken,got it apart. Part #245022 best I can find so far is $1500.00 It fits a few different machines.Its a Clark trans.
  8. O

    Samsung 120-2 No steering,transmission,hydraulics

    I believe your picture is correct #21 may be broken. I was under it this morning and the flange spins freely. Allthough it does have the Clark trans and they typically don't use a spline drive maybe a Bakelite,or flex type drive? Not sure.Looks like I can can get the cover off in the machine.
  9. O

    Samsung 120-2 No steering,transmission,hydraulics

    Just purchased dead! Was told that everything worked @ shutdown on Friday,Monday morning started as normal but, No trans,no steer,no lift,all dead.Engine runs fine drive shaft to converter rotates.I have service and parts books on the way,but in the meantime looking at some pictures it looks...
  10. O

    Cat D5G

    He mite try pulling the filters, open them up and take a look, kinda sounds like the flow may be restricted
  11. O

    Cat 910 steering

    My mid 70s vintage 910 steering doesn't work when cold (45/50 degrees) Can hardly turn the wheel,after running a few minutes,works perfect.Fluid is clean.I did see in the manual there is a valve of some sort under the floor by the master cylinder "flow control and relief valve" I'm thinking of...
  12. O

    TL26 Takeuchi

    TL26 op says working ok,backed up for a new cut stopped,no for or rev on left side.Right side goes a few inches for and rev but stops,and does not pull.Went over with loader to pull out of job site,tracks locked both sides.Questions are,does this model use a cable and pin sprocket brake? And is...
  13. O

    Cat 936F drift

    We do a fair bit of grading with it, and I cannot maintain down pressure without holding it down.
  14. O

    1975 case 450 engine problem

    The 188, and the stroked out version,the 207 are great engines 5-7000 hrs easy.As said some of the best cold starters out there. .Some had rod bearing issues,but were really lake of maintenance issues.Injection pump seemed to be the weak link.
  15. O

    Your dozer photos

    Thanks,the pictures are from last fall.We just finished the new bottom,and blade.Looking forward to getting dirty this spring!Was a U.S. forest service tractor,got 2900 hrs.Thought it was worth saving for sure.
  16. O

    Your dozer photos

    After sitting sixteen years outdoors,I bought this needing a rehab.After new clutches and brakes,paint and now complete bottom and blade rebuild,it's ready to go.It came with the trailer,so it got a rebuild as well?
  17. O

    john Deere 544h oil pressure light

    Ya, I got a Cat 936F doin the same thing.A couple times a day.Shut it down restart pull the idle back as slow as it will run and no light.Almost got to be the sensor.May have to go with a real gauge for a few days to figure it out.
  18. O

    C frame Eye bolts stuck

    Been at it with torch heat, 10 ton porta power and a two pounder today.Tomorrow!!! rose bud and a FBiggerH
  19. O

    C frame Eye bolts stuck

    Rebuilding the blade on my D3B down to the Eye bolts at the rear of C frame,got the nuts off but cant get the eye bolt to budge.Put a pin in it and jacked the tractor up trying to twist it,no luck yet any thoughts?:Banghead
  20. O

    450G blade self aligning bearing

    Have not dealt with them,I think that imports from some countries, you just stay away from.Not sure right now who is building the decent stuff.I think in track parts, Italy is a good source.--Dunno:beatsme
Top