• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. B

    Case 480e 4x4 shuttle shift

    My 480e will not go forward,works fine on reverse. Seams to move ever so slightly in forward.
  2. B

    Cat D4d factory muffler.

    Anyone know the factory oem number for Cat D4D (07R 0735) muffler. I have replaced it with an after market, it is loud doesn’t appear it will last long.
  3. B

    Cat D4D Precleaner

    Any one know the part number for Cat D4D (07R) precleaner bowl/insert.
  4. B

    D4D transmission seal

    Cat D4d (07R 0735) power shift transmission front seal leaking.What is the procedure for replacing this seal and part number. As always thanks for information.
  5. B

    Cat D4D transmission issues

    It’s been a while since have posted anything . So here’s the issue. Cat d4d (7R 0735), went to operate machine one cold morning (28 degrees) machine barely moved in first gear (power shift trans) after 15 minutes warm up machine seemed to operate OK, did not run for extended period. Went back...
  6. B

    Excavator move

    I currently have IH S2500 10 wheeler 15 ft dump,350 cummins 9spd rr ,22.5 better built tag 20 ft tag. I was wondering what size excavator /dozer could be safely hauled.Currently hauling a Ex100 and Cat Lpg Cat d4d.
  7. B

    Cat d4h pivot shaft

    I am looking at a Cat D4H series 2 with worn out pivot shaft on the right side, left side appears fine. I think I am using the right terminology, it’s the support directly below the final drive. How much am I looking at cost wise. Would like to do the repair myself.
  8. B

    Pump Displacement Angle Sensor

    My Ex 100-3 has started to stall under a load , if the controlls are moved slightly it will not stall, but if moved fully it will stall the engine. Anyone experienced this problem. I am thinking a sensor. Possibly the Pump Displacement Angle Sensor.John Deere wants $600 dollars, I have seen them...
  9. B

    Cat d4d growling

    My cat d4d 7R 0735 make growling noise when trying to turn right .almost impossible to make a turn under pressure. Any advise would be greatly appreciated.
  10. B

    Hitachi EX 100-3 fuel Issue

    Hello all,I have a EX 100-3 that seems to have developed a fuel problem. Machine was running fine then started sputtering and die. Remove fuel filter, it was half empty, filled a new one and installed it and machine worked fine for about 15 mins. same issue,machine died again pull fuel filter...
  11. B

    Hitachi ex 100-3

    Considering a Hitachi EX 100-3 , 4100 hrs any one had experience with these machine good or bad.
  12. B

    D4D coolant

    Looking info on the proper coolant/ antifreeze for a 1975 cat d4d , I am flushing the engine and radiator. Also would like to change hoses if anyone knows the part # for upper + lower . thx.
  13. B

    IH 4700 towing capacity

    Any thoughts on hauling a cat d4d (10 tons) with a IH 4700 (Allison mt 653 at) and hudson 12 ton pintle hitch with air brakes .
  14. B

    Lost track frame bracket

    So I have to replace the rails and sprockets on the 07r d4d. Looking under the frame I noticed a bracket missing from the left side of the frame. This bracket is located midway track frame and a support from the belly of the dozer is held in place by said bracket . Anyone know what its name or...
  15. B

    D4d steering clutch adjustment

    Need help with steering clutch adjustment on my 1975 Cat D4d SN 07R0735 . Any help would be greatly appreicated.
  16. B

    D4d steering clutch adjustment linkage

    Need help with steering clutch adjustment on my 1975 d4d 07R0735 (sn) , hoping NIGE or OM can help with this as they are a very great resource . thanks again for all the help in the past .
  17. B

    Cat D4D track adjuster removal & rebuild

    Got the old d4d steering issue resolved. Now on to the track adjuster,the adjuster is leaking , so l am trying to remove it. My issue is l am trying to remove the bolts clamping the arms to the tenioner cylinder. I cut the nuts from back of the clamping part of the arms but bolts will not turn...
  18. B

    D4D Steering clutch linkage parts

    I am in need of the steering clutch adjustment linkage and the roller bearings that the linkage sits in. The adjustment parts are shaped like a doughnut with a stud sticking out the side. Any info or source would be appreicated.
  19. B

    D4d steering clutch linkage parts.

    I am in need of the parts that fits in the clutch forks on both sides of the clutch linkage. The part looks like a doughnut with a stud sticking out one side. I am looking anew or used replacement part , any help would be appreicated. Is this part threaded so a new stud could be installed or is...
  20. B

    D4D Transmission cover removal

    Whats the best way to cut brake linkage loose to remove transmission cover, also is the rod that goes to the clutch fork threaded on both ends. This is a 1975 powershift model.
Top