• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Recent content by mobile-tech

  1. M

    cat 953 steering issue

    hopefully have time to run that machine tomorrow been bouncing around from a engine job,field repairs and pm’s. If it sets a code after I get it good and warmed up continue with the calibration from the t&a file provided.
  2. M

    cat 953 steering issue

    Yes I’ll have to try that - as per the usually I’m bouncing back and forth between repair projects
  3. M

    cat 953 steering issue

    thanks i will proceed with this
  4. M

    cat 953 steering issue

    Access into service mode and was able to clear code , exit out and cycle key check for codes none present
  5. M

    cat 953 steering issue

    the code doesnt have serv code lit up next to it so it must not be a current fault -per the troubleshooting
  6. M

    cat 953 steering issue

    hello, thank you- back to the yard soon and I’ll go from here
  7. M

    cat 953 steering issue

    have a 953 2zn03684 -machine has right at 7k on it - came in from job said it didnt turn, ran it in the yard for 15-25 min seemed fine the heat wasnt working and i thought they might just wanted a different machine back at another job worked fine til machine got good and hot after a few hours...
  8. M

    terex tracpactor 428 rotor hardfacing

    thanks for the reply i got ahold of terex and forwarded me the ESAB brand wire they recommend, unfortunately not available here in the united states , had my welding supplier cross onto something compatible and got it done
  9. M

    terex tracpactor 428 rotor hardfacing

    have our tracpactor 428 pulled down for new rotor bearings, figured i would build back up the hard face anyone know what hardfacing material to use i got it in the shop and have a big mig-spray arc setup -last hardface i did was on a genesis concrete processor and got the wire right from them ...
  10. M

    cat 320c logged errors and events derates

    thank you
  11. M

    cat 320c logged errors and events derates

    need some help with a 320c here no ET , pulled logged errors and logged events off monitor PAB04558 69: 96-03 69:587-03 69:376-05 69:110-10 69:190-10 69:167-08 69:190-08 69:588-09 logged errors.... just replaced monitor as it was inop and i couldnt get any function on it logged events 69:100...
  12. M

    D6t LGP blade inop with codes

    tested everything out sensor was bad at joystick base , i did have gps disconnected to test as it was setting codes that where not really active , new joystick base everything worked , reinstalled gps harness and everything is functioning correctly , reinstalled all the panels and seat now im...
  13. M

    D6t LGP blade inop with codes

    thanks , friday was hectic and i was under the weather all weekend and monday, back at it today , i gota cummins that was supposed to be a easy job turning in to a much larger project , hopefully get some time to workk on dozer today we will see
  14. M

    D6t LGP blade inop with codes

    i proceeeded with sent dianostic information , i disconnected top con harness from solenoids and pluged machines plugs into corresponding solenoids ,the 4 codes went inactive . start machine blade raises and tilts if pressure is kept on joystick , if i let off and try and raise or tilt or lower...
  15. M

    D6t LGP blade inop with codes

    thank you Nige
See more
Top