• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. F

    10amp circuit breaker keeps popping

    sorry TxHayseed, seems like i can't find it. went through service manual twice yesterday and didn't see level sensor replacement. could you please post it for me. thanks
  2. F

    10amp circuit breaker keeps popping

    thanks guys. just got my digital level so will try that. txhayseed do you have the values for using volt meter? i would like to try that ,too.
  3. F

    10amp circuit breaker keeps popping

    thank you, i also had damaged wires under machine and repaired them and put the split plastic wire loom over them. circuit breaker is not popping now. still trying to get tilt sensor level. just ordered small digital level to use on top of sensor to try and set it.
  4. F

    genie boomlift decreased groundspeed

    it is working. thanks for all the help. i had 1 wire wrong on the limit switch by the turn table. and i checked connections of tilt sensor to ground control panel. thanks , bruce
  5. F

    genie boomlift decreased groundspeed

    when the joy stick is pushed forward or backwards it will move faster the more it is pushed. i don't know how to test it as there are 3 parts that rotate and a number of wires.
  6. F

    genie boomlift decreased groundspeed

    still have problem with ground speed. i put on 2 new limit switches. did the flow chart for machine will not drive at full speed and it all check out ok, and no fault codes. but there are 4 limit switches and it does not show how to check out ?#3 limit switch which i think is the 1 down under...
  7. F

    bobcat 863 blowing seals in carrier

    thanks for all the help. once i got the hyd. lines connected correctly it works great. bruce
  8. F

    bobcat 863 blowing seals in carrier

    thank you, i'll try and put it together this weekend. looks like i have 1 to go to tank drain and 1 to go to hyd pump.
  9. F

    bobcat 863 blowing seals in carrier

    i think i screwed up royally. i had to disconnect all the hoses and tubes when i replaced axle bearings and races. i did not mark all the hoses. i took lots of pics but not enough. does anyone have a diagram of which hoses go to which end of drain filter?
  10. F

    bobcat 863 blowing seals in carrier

    i did put a new drain filter in when overhauling this machine. it doesn't even have a hr of time on it, but i will reck it. my hydrostatic motor and carrier is very different from final drive in video. the fluid from hydrostatic motor flow blows the seals in carrier , then into chain case and...
  11. F

    bobcat 863 blowing seals in carrier

    still working on my 863. the hydrostatic motor carrier blows out the seals twice within minutes of moving it. took to dealer and it happened to them twice also. last time up on blocks it ran ok for 15min. , then when on ground blew out within 5 min. brought it home. took hydrostatic motor apart...
  12. F

    genie boomlift decreased groundspeed

    thank you for all the help. i think i found the problem in the proximity switches. 3 had good resistance but 1 was very rusted and no resistance. so ordered 1 and hope it fixes problem. voltage was good. no fault codes, most of other functions work except platform does not swivel, i am checking...
  13. F

    genie boomlift decreased groundspeed

    genie z34/22dc, electric motors. ground speed had been good, sat for a month and now very slow ground speed both forward and reverse, will not go faster. checked all batteries and they are good. have 51 volts to pr2 solenoid. not sure how to check ? on forward/reverse control in basket or...
  14. F

    Bobcat 863 fault code 33-23

    I guess bobcat dealer forgot to tell me that. My 1st skidsteer and sure has been frustrating. Thank you
  15. F

    Bobcat 863 fault code 33-23

    I put new controller in and everything worked fine but before I could put bucket back on lift and tilt would not work. Have code 33-23. I can not find any bad wiring. Remove each harness from controller and reconnected them. Battery is new and holds charge. I disconnected battery before working...
  16. F

    bobcat 863 code 33-23 and 13-07

    still working on this salvage project. the lift arms and tilt do not work. no warning lights on and all for lites are on for lift arms to work. the other problem that may be related is brake solenoid shaft, etc falls down in chain case. when i test the solenoid with battery , it pulls in with...
  17. F

    bobcat 863 disc brake assembly bolt breaking

    help. what am i screwing up for 2nd time. my disc brake assembly bolt breaks and everything falls into chain case. tested solenoid and it works pulling shaft in. is solenoid the only thing that holds wedge up?
  18. F

    drive wheel traction

    sorry, i should of posted pix to start. thanks for the responses. looks like fun in the water. still wondering if both drive wheels should turn or spin on wet ground and it chains on tires will hurt electric motors' thank you
  19. F

    drive wheel traction

    34/22dc genie boom lift. can i put snow chains on drive tires or put different tires with big tread for better traction. would this hurt the electric motors? does only 1 tire spin when on mud or should both? i was hoping to use machine around job sites but maybe it is only built for concrete...
  20. F

    hydraulic pressure testing

    Update , success . replaced counterbalance valve and holds jib boom.
Top