• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. B

    Sullair 185 Compressor stalls

    Carbureted I presume, what temps are you talking? Being Canada it could be lower BC which the temps can be mild to the NW territories which is damn cold. It's not unusual to have to let an engine run in cold temps before it warms and the manifold will keep the gasoline atomized. 15 Minutes seems...
  2. B

    HYSTER H 3.50XL

    Give us a little more info, when you put it in gear (forward) and let out the clutch is there any response at all? Like, does the engine sound change or a slight jerk in the drive train or is it completely dead. Does the linkage feel like it is doing anything and will it grind if you don't push...
  3. B

    844 Lull cylinder help?

    What model A, B, C, and how many section boom (2 or 3)? If it has never been apart and lubed you are going to need a whole lot more than a BFH. All the way from a rosebud to a oxy lance.As tight as it probably is, it's usually a multistep process until you find what works. I have had to cut the...
  4. B

    Forklift: Powersupply instead Battery

    A (standard) switching supply won't work with this kind of a load as it appears as a dead short until the motor produces sufficient cemf. The load demand would be greater than the power supply could produce. If you have access to a standard 12 volt deep cycle battery (marine), for the little...
  5. B

    Linde H50D Issues

    For that series your codes all refer to the lift system (lift, tilt, etc) and may be "possibly" caused by an out of calibration joystick. Do you have a diagnostic adapter and laptop to troubleshoot with? You could be having a controller failure L/D but I think you may be better off having the...
  6. B

    Linde H50D Issues

    Sounds like a charging system problem or the main harness connector giving a low voltage signal (affects everything). Put a volt meter on the battery when the problem exits and then on the fuse panel. The voltage should be the same (or very close), if it is go to the control and see what it...
  7. B

    CLARK 2015 PARTS NUMBER HELP LIFT CYLINDER SEAL KIT(approximately mid 1950 model)

    You really don't need a part number as a kit from Clark or any other supplier probably doesn't exist anymore (and considering the time it sat on the shelf, you wouldn't want it). That said this cylinder originally used leather cups or vee (chevron) packings. If no one has modified it just take...
  8. B

    T50C serial number identification

    1984 or 85, 1404 engine (Hercules 140)
  9. B

    55 Michigan Transmission woes

    It’s right on the bottom, lowest point of the transmission.
  10. B

    55 Michigan Transmission woes

    What is the complete model, 55A or B or later. If it"s an A or B then the sump screen is at the bottom under the bottom cover. There are a dozen or so bolts to remove to take off the bottom sump. The screen is in there.
  11. B

    Hyster shop manuals?

    Post a pic of the serial / model number plate. I Have E50B manuals but the numbers don't fit.
  12. B

    Cat v60b steering help

    This may be the correct manual, I didn't mark what the application was.
  13. B

    clark 110-11b

    You will need about 6" to clear everything, I can't remember the bolt count which designates the specific gear. I think it was 16 but don't depend on that.
  14. B

    Cat v60b steering help

    There is only one centering spring.
  15. B

    clark 110-11b

    Unless you're married to Jeannie or Samantha I would say so.
  16. B

    clark 110-11b

    Depends on if it has ever been changed but, they used a fiber internal gear mounted to the flywheel and an external steel gear on the converter. Usually the fiber gear fails and the converter gear just turns inside it. Some people changed them to steel but it was noisy (thus the reason for...
  17. B

    Cat v60b steering help

    If the serial number plate is gone, look at the front frame crossmember right side where the tilt cylinder goes through. It should be stamped in that plate. What steering system do you have is it the original hydraulic assist mechanical steering or hydrostatic steering? Hydrostatic is just...
  18. B

    Hyster YE 40 flywheel removal

    Use a block of wood that you can put through the starter hole and and give it a good rap. if it doesn't come loose, turn the engine over 180 degrees and do it again. Keep at it until it comes loose, use a hardwood so it's a little more solid.
  19. B

    Hyster YT 40 Differential

    Good luck, that truck is around 60 years old and Hyster didn't maintain much parts stock when they were 15. That said try...
Top