• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. Eric a1cnc

    68 580 ck injection pump question

    There are actually (2) tools for the Umbrella seals. After you install the pump keep an Eagle eye on your oil level. If the umbrella seals roll or just don't seal right your oil level will rise indicating you are filling the base with diesel... NOT GOOD. You can also have fuel bypass faulty...
  2. Eric a1cnc

    580ck injection pump question

    I do know about the R/R dim being different thanks. So far both have been set for the 30AJ. The first time I put the one together for my dozer I didn't check the setting figuring it was right before. I couldn't get much power out of a newly rebuilt engine. Pulled the pump back off and checked...
  3. Eric a1cnc

    580ck injection pump question

    No competition here, Just using what I've learned from you. Big thank you to you
  4. Eric a1cnc

    580ck injection pump question

    It got a new liner and blades, The rotor and the rest of the innards were apparently not subject to the water. No signs of pitting on anywhere else. I fully dis-assembled it and the outside was the only pitted spot. Pulled everything out, inspected/ cleaned in an ultrasonic. Metering valve and...
  5. Eric a1cnc

    580ck injection pump question

    Maybe a picture will be better
  6. Eric a1cnc

    580ck injection pump question

    Thanks Pump guy, The c-clip will go on no problem. The original design plates have a recess milled into the back side and it sits nearly touching the cam ring where as the new design leaves 3/32" space. Just looked different and didn't want to put it together wrong
  7. Eric a1cnc

    580ck injection pump question

    Now that summer is over I am back working on my 580. I am putting the injection pump back together with a 1 piece weight retainer. There is a larger gap between the Cam ring and the 1 piece weight retainer than there was with the original. The injection pump is a DBGFCC431-30AJ Is there...
  8. Eric a1cnc

    Broken injector pump drive shaft case 530ck 188 diesel

    No, I have been so busy with work this week I didn't have a chance to do anything on it yet
  9. Eric a1cnc

    Broken injector pump drive shaft case 530ck 188 diesel

    I have the service manual thanks, and I have a pop tester. On my dozer I ended up finding a place nearby that sells new stanadyne injectors.
  10. Eric a1cnc

    Broken injector pump drive shaft case 530ck 188 diesel

    This is going to be interesting.. I was planning on pulling the injectors any ways to test them. Guess until I get the front plate off I won't know for sure where I am.
  11. Eric a1cnc

    Broken injector pump drive shaft case 530ck 188 diesel

    I aligned the timing mark on the flywheel before I took off the pump. Do you think that will be ok then?
  12. Eric a1cnc

    Broken injector pump drive shaft case 530ck 188 diesel

    Thanks, I do know a bit about the engines. I rebuilt one for my dozer a year or so ago. I know about the spring and plunger. I have a spare driveshaft and gear so I have those parts. I know enough to try to align all the marks on the gears and timing mark before taking it apart. I am pretty...
  13. Eric a1cnc

    Broken injector pump drive shaft case 530ck 188 diesel

    Thanks Pump guy, I figured there would have to be a reason for the shaft to snap. I believe it could have been sucking dirt as there is some debris in the top of the pump. I changed the filters last fall but i guess that didn't help. With the top off I can see one of the governor weights has...
  14. Eric a1cnc

    Broken injector pump drive shaft case 530ck 188 diesel

    My 530 was running fine. I pulled forward down hill a bit and it acted like it ran out of fuel. I put in 10 gallons of fuel and couldn't get it to prime. I pulled the inspection window off the side of the pump and it wasn't turning. I used the timing marks on the flywheel to hopefully line it...
  15. Eric a1cnc

    Case 530 CK shift problems

    I would appreciate those pictures if you could. I have almost the same issue except mine only pops out of low going forward. It is fine in reverse but will pop out instantly in forward low
  16. Eric a1cnc

    Model 32 backhoe

    I have a 1968 530ck with the same issue. The Po on mine liked to weld everything A LOT! The welds on my arm to frame are all busted. Where welding the backhoe permanently becomes an issue is that if you ever have to work on the backhoe control valves. It would be FAR easier to be able to remove...
  17. Eric a1cnc

    Case 350 oil level too high after sitting

    I let it sit well over 24 hours. I don't remember the tube part # but it was the same length as the one I took out and I put the new one in stinking out the same amount. Measured with calipers.
  18. Eric a1cnc

    Case 350 oil level too high after sitting

    I used 5 minute epoxy. I was wondering if that could be the problem. No groove it the tube. It looks as good as it did when I put it in new. I did have a crease in the seal that was towards away from the motor but I am pretty sure that happened as I took it out, I could feel it roll. I was...
  19. Eric a1cnc

    Case 350 oil level too high after sitting

    Here I am again with the same problem, SIGH. I replaced the lip seals on the shaft for the 3rd time Assuming that is what is causing fuel to get into the oil. I replaced them 2-3 weeks ago, ran the dozer for a couple hours and when I shut it down the oil level was perfect. Now after it having...
  20. Eric a1cnc

    Case 580CK diesel head gasket install

    Your'e making it too hard. Loosen all the timing cover bolts/nuts. Then, wedge (GENTLY) something between the cover and block to give a little space. If I remember from when I did mine there might be a couple places to tap a screwdriver in between the block and the cover that is NOT between the...
Top