• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. L

    Bobcat s300 shuts down shortly after start.

    Thanks for that explanation on the wiper. Cooling fan is belt driven. I do have a service manual and parts manual, also an owners manual on order. 05-15 was due to several fittings that were loosened I was not aware of. Thankful for that. I do have 15-02 and 16-07 now. I looked them up on the...
  2. L

    Bobcat s300 shuts down shortly after start.

    The drive belt is tight. I've tried to find posts on the charge pressure subject, not much luck. Looking for some more good suggestions. Thanks
  3. L

    Bobcat s300 shuts down shortly after start.

    I'll check the filter and other posts. On the 12-22, I don't have a door or wiper. Thanks for your help.
  4. L

    Bobcat s300 shuts down shortly after start.

    I'll check the belt. Did you happen to see my question on moving the machine slowly with one rear drive chain missing. It's about 3/4 mile. Thanks again for your help. Very appreciated.
  5. L

    Bobcat s300 shuts down shortly after start.

    Thank you for the response. Where do you find the list of fault codes for this machine? The list I found didn't show 16-01, 05-15 was high hyd. charge pressure level of emergency shutdown, 12-22 is PWM controller front additional hydraulics at lower limit of range. Can you give me some ideas on...
  6. L

    Bobcat s300 shuts down shortly after start.

    Long beep after engine started. 3 beeps after engine ran shortly. Then shut down. Codes were 16-01, 05-15, 12-22. I couldn't find 16-01, but I did the others. Don't know what they mean. I'm trying to find out. Engine shuts down at 25 seconds each time it starts. Thanks for your help.
  7. L

    Bobcat s300 shuts down shortly after start.

    Thanks for your response. I have a generator running for a battery charger, didn't notice any beeps,(hearing is not good on high pitched anyway). I'm in some woods. I'll try something different on battery and check the beeps. Also, it has a broken right rear drive chain. Will I be able to take...
  8. L

    Bobcat s300 shuts down shortly after start.

    Newbie here. Know nothing about skid steers, but I'll learn. I'm reviving an '05 Bobcat S300, Kubota 3300 engine, that's been sitting for several years. Got it started. After it blew a lot of crap out, runs ok. Shuts down after running about 15-20 seconds. It will start right back up. It does...
  9. L

    NH LT190B feedback

    Newbie here. Can I get a little background on the LT190b. I looking at one with 430 hrs at an upcoming estate auction. Value, problems, etc. And the last year they were manufactured? Thanks for your help.
  10. L

    Case 450c long track bode control valve

    I'll try to remember to do that whenever I get to fixing them, and figure what will work best.
  11. L

    Case 450c long track bode control valve

    Thanks for responding. I'll have to look at things again and see if what you're suggesting will work. Someone had welded some crap on the end of one spool in the past. It's a mess. Do you think a hydraulic shop would be able to find replacement spools for that valve? Thanks
  12. L

    Case 450c long track bode control valve

    Thanks for the reply. My raise and lower work ok, but with a lot of slop. To tilt, I nearly have to use both hands due to slop and binding. Someone had cobble welded some pieces on the ends of two of the spools for bushings, but one is almost worn through. I'm hoping to get a reply from...
  13. L

    Case 450c long track bode control valve

    Good info, I'm having the same issues with the linkages and bushings. Can you please tell me how much trouble it is to remove the "spools", I believe they're called, to rebuild the ends with bushings? I haven't attempted this project yet. Thanks for your help.
Top