• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. bad Tom

    Case 440 self leveling problems

    Left handle controls the hydraulic functions on the front of the boom. The right handle controls the functions of the front electric connecter.
  2. bad Tom

    Case 440 self leveling problems

    KSSS is correct about the operation. I field installed the self leveling on my 420 and it didn't take much time to learn how to use it.
  3. bad Tom

    Service Manual

    I bought all of mine from ebay.
  4. bad Tom

    2008 Case 440CT-3 Skid Steer good or bad?

    My early 440CT has C block tracks and I can spin them at a dead idle. It really does not need 89 horse power but I like having it.
  5. bad Tom

    1845c external hydraulics

    I have no specs for the 1845C but the 1835C has a flow of 16.4 GPM and a pressure of 2250 PSI. You can rum any standard flow machine. You would have to run your engine faster than the newer machines to get the same result. Forget the high flow, that would take a lot of time and money.
  6. bad Tom

    1845 to 1845c parts compatibility.

    1979 year
  7. bad Tom

    Running a low flow brush cutter on a high flow machine

    I don't think you could do any damage to the loader running it at that rpm. I don't run my loaders wide open now.
  8. bad Tom

    1845C, needle bearings in drive chain box

    How about slacking off the drive chains and then try to shake the drive gear with a pry bar and see if it's got play in it. I would do that first and go from there.
  9. bad Tom

    Running a low flow brush cutter on a high flow machine

    The only way to know how much flow you have is connect to a flow meter and check it at different engine speeds. The brush cutter I have is for 15 to 25 GPM. The hydraulic motor is only 20 GPM max. I am running more gallons a minute more than it can handle and I had to replace the control valve...
  10. bad Tom

    HTO fluid solution?

    You can go to any ag CaseIH dealer Like KanEquip in Topeka or a dealer in Smithville.
  11. bad Tom

    Case 90XT

    It's called a "filter head" and the part number is 87439984. Hopes this helps.
  12. bad Tom

    HTO fluid solution?

    I have mixed and matched different oils over the years and had no problems. The 10 wt oil is rated for temps between -10 and 70°, where the 10w30 will work past 112°. I don't see any problems going to rotella,
  13. bad Tom

    Case 1840 was cranking over now just clicks

    Take the pin out of each boom cylinder and use a chain hoist or loader and raise the boom and lock it up, then slide the cab forward to get to the starter.
  14. bad Tom

    Case 1840 was cranking over now just clicks

    I would start looking at the battery cables. They can look good but melt the solder on the inside at the terminals. Another area is the connection at the starter where the cable connects. They can come loose or need cleaning.
  15. bad Tom

    SR200 start but no go

    I have no wiring diagrams for newer machines, just some of the 400 series. I didn't find much in a internet search. I would look for more mouse damage in there.
  16. bad Tom

    SR200 start but no go

    My chart said 9406 is no CAN communication from VCM.
  17. bad Tom

    Case 450 hard starting and smokes

    In your first post, you said it will fire up and run fine sometimes. This should NOT be the problem that you have, but years ago, a customer had a tractor that would not run faster than a idle. I found that the muffler was plugged up and would barely run. Have you tried it without the muffler?
  18. bad Tom

    Case 1840 Serial Number to Year manufactured

    Duane, my book listed it as a early 1995.
  19. bad Tom

    Which brand of skidsteers or most DYI friendly

    My neighbor went to the farm show in Topeka and I showed him the new Deere. You can't see the top of the engine in it. All covered up, you take the side covers off to get into the engine area. With the loader boom lowered, its not fun to work on. We looked at the Case and you can still see the...
  20. bad Tom

    Case 1845C loader hydraulic issue, goes up, wont go down

    Not having worked on a problem like you have, I did have a similar experience with one of my 400 series. I had pushed down on the aux outlet petal partway and that messed up the loader functions. You may have done the same thing.
Top