• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. J

    KVGT issue

    Saturday 4/27/2024 My 2013 PC240LC-10 generated this same L03 CA2387 code last week. I used the information gathered from this post to help me determine what was causing it. I removed the servo block, or what I assume is the servo block, to access the mechanical arm of the gate inside the...
  2. J

    2007 Link Belt 210LX Instrument cluster

    Anyone know if I can change the instrument cluster in my 210LX without having the hours reset to zero? Or would the hours be stored in the actual computer?
  3. J

    Case 650K Series 3 electrical issues

    No voltage to any switches, Horn or buzzer. Only thing I can figure is burned wires. Gotta go through them one by one tomorrow because all the fuses and relays are good.
  4. J

    Case 650K Series 3 electrical issues

    Also, why would the warning buzzer, horn and menu buttons not be getting power? I'll be trying to diagnose these the next couple days
  5. J

    Case 650K Series 3 electrical issues

    That's good to know Coy, I used a tester to see if the machine would move and it did work. What I am afraid of is the machine having an underlying issue that causes the FNR to fail. I haven't actually purchased a new FNR yet until I can hopefully know that the new one wont fail after a short...
  6. J

    Case 650K Series 3 electrical issues

    Anyone heard of any other issues on this model machine causing FNR joy sticks to fail pre mature?
  7. J

    Case 650K Series 3 electrical issues

    Got it moving!! Parking brake pressure solenoid and a new joystick did the trick. The start relay socket was too loose and had to be replaced as well. Starting from the key now but its intermittent. Still no power to the menu buttons.
  8. J

    Case 850K won't move foward or reverse

    Bush_S2k, have you been able to successfully repair one of those joysticks yet? I have two from a case 650K series 3 I could get you to work one of them.
  9. J

    Case 650K Series 3 electrical issues

    What does a flashing “F” mean on the dash? Also, no power to menu switches, Horn, warning buzzer. Can’t see codes because I cannot get power to the buttons
  10. J

    Case 650K Series 3 electrical issues

    Thanks Katfish, good info
  11. J

    Case 650K Series 3 electrical issues

    Got It Coy, there is a bolt right through the center! Thanks a lot man!
  12. J

    Case 650K Series 3 electrical issues

    I didn’t Coy but that’s a good idea Thanks
  13. J

    Case 650K Series 3 electrical issues

    Trying to get this plug apart is a nightmare! The manual refers to these connectors as C4 and M10. My open circuit testing guide led me to this particular connector next and its not wanting to come apart, I'm afraid I'll damage it if I pry too hard. Anyone know if they require a special tool...
  14. J

    Case 650K Series 3 electrical issues

    Anyone happen to know the specifics on those CAN BUS resistors other than being 120 ohm?
  15. J

    Case 650K Series 3 electrical issues

    I located the "CAN" resistor in the back of the dash and it doesn't have continuity, zero ohms. White wire has 3.6v black wire has 4.1v. That's with the key on, safety levers up
  16. J

    Case 650K Series 3 electrical issues

    Anyone know if it is possible to get the instrument cluster and the joystick tested ?
  17. J

    Case 650K Series 3 electrical issues

    Got the right side proximity switch replaced and the orange/green lights are working on both sides like they should now. Machine still doesn't start from the key nor does it travel.
  18. J

    Case 650K Series 3 electrical issues

  19. J

    Case 650K Series 3 electrical issues

  20. J

    Case 650K Series 3 electrical issues

    The right side proximity switch (smooth grey sheathing over blue black and brown)wires were severed and someone tried repairing them and did a terrible job. Two of the wires were not connected. I’ll get that fixed before I move forward. also noticed what appears to be two additional relays...
Top