• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. R

    Cat C7 No Go--Flat won't run--Help troubleshooting please

    We found that the timing gear on the cam shaft had been pushed partially off. We think maybe during the installation of the truck air compressor the gears weren't aligned and this aided in pushing the gear out of position.
  2. R

    Cat C7 No Go--Flat won't run--Help troubleshooting please

    Update if it matters. The engine is a 1998 3126B rather than a C7.
  3. R

    Cat C7 No Go--Flat won't run--Help troubleshooting please

    We replaced the harness. That was our first thought. After that, all parts were at the troubleshooting and recommendation of CAT tech. I hope that's not considered shotgunning parts. I agree on the ether. That just means it's getting air. Cranking oil pressure is like 1200 or something...
  4. R

    Cat C7 No Go--Flat won't run--Help troubleshooting please

    Serial number 7AS07315 arrangement number 154-1062. The truck broke down on the side of the road and we replaced a timing sensor and were back up and running. Two weeks later it died on a job. We have spent 40 hours on it and T&E Cat has spent 40 hours on it. We replaced the lift/transfer pump...
  5. R

    2008 EC-140BLC Fault 140 SID 230 9

    Forget that I asked. The harness had become completely disconnected from one of the ECM's. Not sure which one.
  6. R

    2008 EC-140BLC Fault 140 SID 230 9

    The fault code appeared and the machine was stuck in high idle. After turning the machine on and then off again the machine is now stuck in low idle. Can anyone help? I see a lof of fault codes that are almost the same but the "140" part is usually a different number. Thanks. SN 117xx
  7. R

    Hydraulic Pump Cross Reference

    Wouldn't it be handy though to have a reference on a board like this for everyone though? Here is what I've come up with so far: SNs PIN: 1FF470GX_ _E470001- --Pump PN FYA00035147 FYA00052949 4699645 PG202165 H5V200DPH (yes its a Kawasaki pump!!!)
  8. R

    Hydraulic Pump Cross Reference

    Yes, there is and it matches one of the part numbers I listed but that's just the Deere number. It doesn't' answer the cross-reference question.
  9. R

    Hydraulic Pump Cross Reference

    Does anyone know of a source that could provide insight into which pump is in which excavator? I am currently working with a JD 470GLC and there appear to be many pump options: (not the serial number range I am working with) SNs PIN: 1FF470GX_ _C047001- --Pump PN 9184686EX (I am working with...
  10. R

    Volvo EC160B Error Code

    I've got an error code 187 PPID 1190 4 Operator says: "ex is broke down wont move nothing works i shut it off and tried to restart it and i have no power at all no lights no anything " Now what?
  11. R

    Deere GLC Series Excavator Door Latch--Repair Help

    I do mean the cable assembly. The parts diagram shows clips that hold the cable assembly in place within the door. I assumed I would need to reattach those.
  12. R

    Deere GLC Series Excavator Door Latch--Repair Help

    We have a JD 470GLC and the latch that holds the door open broke. I was able to purchase the parts but our repair manual does not show us how to install the latch. It appears that the door is a sealed unit and we cannot access the cable to replace it without cutting open the door with a torch...
  13. R

    Case Excavator

    I have this code on a Case 470C !0101 Any help?
  14. R

    2002 Cat 246 questions

    This is getting more in-depth than my knowledge or data from our in house mechanic. If we could ignore the potential to rebuild the engine I'd like to focus on if $9,000 is really what I should expect to pay on a reman or if there are other engine options that essentially fit in this machine.
  15. R

    2002 Cat 246 questions

    This gets into a bit more detail than I know. They say it turns by hand very nicely but when assembled and operated it has a horrible clatter. I believe the engine was then disassembled and on closer inspection, the "walking" was discovered. Not being much of a mechanic "main bearing" was...
  16. R

    2002 Cat 246 questions

    I've got a Cat 246B question so I hope it's appropriate to add to this thread. I need an engine or at least I think I do. The engine is a Cat 3044C-T Arrangement 179-1854 My shop mechanic tells me the crankshaft is walking in the engine. I would assume that the crankshaft has some type of...
  17. R

    252B sometimes won't move or engage high gear

    Is the little motor on top of the fuel filter a pump? If so does it normally run when the key is in "run" or does it have a pressure switch and it keeps running because it can't get fuel and create enough pressure to shut off?
  18. R

    252B sometimes won't move or engage high gear

    From what I can tell there is only one filter which I assume is a combination filter and water separator. There is no water in the bottom bowl. I do have a new filter and some 911 and will give that a try.
  19. R

    252B sometimes won't move or engage high gear

    I replaced the battery but I now have a new problem. The machine won't start. Well, as soon as I replaced the battery the machine started and ran for about 30 seconds then died. I attempted to start again and it ran for about two minutes then died. While it was running it was not responsive...
  20. R

    JD 470G Counter Weight Removal

    I think it might be not leaving the lever up.
Top