• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. A

    Engine speed sensor code

    It won't start if we plug primary or both sensor but if just secondary sensor it starts but not easily
  2. A

    Engine speed sensor code

    Another question is, the manual says it should run on either speed sensor but we can only get it to start on the secondary speed sensor, if we plug the primary sensor in it will shut down immediately and if we try to start it on the primary speed center it just says configuration pending on the...
  3. A

    Engine speed sensor code

    Hi got the engine totally rebuilt again and there no blow by anymore but still starts only sometimes and haven't really been able to figure out when it does and does not I just noticed sometimes when starting injection disabled was "on" can anyone help me out why that would be?
  4. A

    299D DTC Codes / Engine Problems

    My guess is you need a new engine wire harness DTC 144-5 (Backup Alarm Relay Current Below Normal) could be just a missing relay in the fuse panel DTC 3700-3 (Loader Bucket Inclinometer Sensor Voltage Above Normal)it's common for the wire to hookup plate to get damaged, either get the sensor...
  5. A

    Cat 299D2 Hydraulic Coupler Replacement

    That's how I always do it
  6. A

    Cat/ FAE - HM312 Forest Mulcher - Connections to 299D2

    You probably figured this out by now but the c series hi flow had 2 HYD function on boom and d series only have 1 HYD function so the door will not work without a valve installed on mulcher, my HM415 has the valve block but it also has 2 plugged port labeled door that I think would be to hook...
  7. A

    Need AC wiring schematic for a CAT 259D Compact Track Loader

    I find on d series if the 2 pressure sensors by compressor have continuity then u know it's charged yet then I've seen the temp switch fail in heater box under feet and if those sensors are open then the most likely spot for it to leak is the hose going out to condenser where rear door pivots...
  8. A

    Engine speed sensor code

    what should this be and how much tolerance does it have? this would make the most sense if 1 of the teeth would be just borderline close enough.
  9. A

    Engine speed sensor code

    I still havent been able to figure this one out it has to be either ecm, harness, sensor or engine its self Are you sure nige that you posted the correct speed timing test my primary and secondary sensor are the same (2wire) and different locations then the diagrams any heres where im at...
  10. A

    Engine speed sensor code

    I don't have the tool to lock no, can make out what this picture is show it looks like it might be another way of checking the timing in fuel pump.
  11. A

    Engine speed sensor code

    Would you also have the file, Disassembly and Assembly, "Fuel Injection Pump Gear - Install"
  12. A

    Engine speed sensor code

    Thanks is cyl 1 at the flywheel or fan end?
  13. A

    Engine speed sensor code

    Thanks do u also have the Doc "Finding Top Center Position for No. 1 Piston".
  14. A

    Engine speed sensor code

    Finally working on this project again and found this out 1 tooth what is the process to time the middle idler to the crank shaft?
  15. A

    Engine speed sensor code

    Hello I have a engine that brings up code 190-8 since it was rebuilt I put a new senser on and that didn't help attached are some graphes that might be helpful It's on a cat TL1055 telehandler S\N TBM00416 Engine number is 292-5307 Might it be a grounding issue?
  16. A

    Cat 259d Aftertreatment alarm

    Is soot load percentage something different that what you mean, as per picture above that's at 16. No I don't believe DPF has ever been cleaned.
  17. A

    Cat 259d Aftertreatment alarm

    i had set this machine aside for now but so you are saying the dpf being full is kind of the least possibility is there ant way of knowing if the dpf is full or if its wiring/sensor problem? can anyone tell me what perameters the engine watches to know when to trigger a regen so i have somewhere...
  18. A

    Cat 259d Aftertreatment alarm

    So my best bet is to just get it cleaned ? The differential pressure sensor don't really tell me if it's time to or not? we generally stop the skidsteer instead of letting it idle when not so it has mostly half decent hard working hrs. Can you send that cleaning procedure?
  19. A

    Cat 259d Aftertreatment alarm

    the fan belt was once broken last when it overheated, can i go by the soot loading percent to know if dpf has to be cleaned? thanks
  20. A

    Cat 259d Aftertreatment alarm

    hello my 259d FTL01273 2600hrs is giving me code 523602-0 excessive regeneration frequency thats when it trys to do a active regeneration within 30 minutes of each other ( I have ET) what should i be watching on engine status to figure out whats triggering a regeneration? attatched is some...
Top