• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. W

    Thumb teeth hitting bucket teeth

    I just got a new 30in bucket for my 442 Bobcat and the thumb teeth hit dead center on bucket teeth, was wondering if this will cause a problem, all my other machines with thumbs hit between bucket teeth.
  2. W

    Oil in bell housing

    My JD 200 lc starter was acting up so I pulled it off and there was a lot of oil on the starter, when we tore it down the starter had oil inside of it, my question is should there be oil in the bell housing or do I have a leaking rear main seal.
  3. W

    john deere 200lc throttle problem and more......

    ser#ff0200x501452. Machine was running fine and shut down suddenly,will start and shut off when trying to restart. I found the solenoid that shuts off the fuel will open and machine will start,immediately upon starting the solinenoid will close and shut off fuel. If I continue cranking it will...
  4. W

    John Deere 4120 fuel injector problems

    I replaced the fuel injector assemblies in my brothers tractor, got it back running and changed the oil and filter because of fuel in the oil,ran it for a few minutes and it ran fine, checked the oil level and it is way over full and has fuel in it,Thanks for any help. Engine is a 4024t
  5. W

    John Deere 200LC warning lights

    The charge and oil pressure lights stay on after engine is shut down, I can disconnect the battery and reconnect it and the lights will go out and stay out until it is restarted and shut down.Anyone have an idea of where I need to start looking to fix this!
  6. W

    John Deere 200lc injectors question

    I am rebuilding the engine for my excavator and was looking for new injectors,I found some at Complete Tractor that are new and are around 35.00 each, these are the pencil type injectors, does this price seem too cheap, I do not want to have to redo this engine because of a cheap or wrong injector.
  7. W

    Rubber boots for joy sucks on Galion 503 l

    Anyone know a source for these or a part number.
  8. W

    Galion 503 L injector pump timing UD236 IH

    I pulled the pump to have it rebuilt, put the engine at TDC, removed small inspection cover on the front of the engine and removed the nut from the pump shaft and removed the pump.There is a key way on the pump shaft that goes thru the gear, after rebuilding the pump I lined up everything as it...
  9. W

    Galion 503 l throttle cable

    I need a throttle cable or a part number for the cable,it has an International diesel engine,any help would be appreciated.
  10. W

    2 Allis Chalmers 65 motor graders for parts

    I am selling 2 graders for parts, I am located near Florence SC 1 was a parts machine,no motor or rear drives, has transmission, good turn table, other machine was in use but sucked dirt and ruined engine,I was going to rebuild but found out today that the head is cracked, block and crankshaft...
  11. W

    Need Help!!!

    Anybody on here in the Bushnell Fl. area that can inspect a 200 lc that I am thinking about buying!
  12. W

    D31-17 Transmission Shifting Question

    I hired a new operator, he is an older experienced operator but I dont like the way he shifts from forward to reverse and vice versa on my dozer. Can someone tell me the correct way this should be done on this particular machine. Thanks
  13. W

    John Deere 200 lc serial number search

    I have a 200 lc ser#ff0200x501452 I am looking at another excavator ser#ff0200x050856 and was wondering if someone could tell me the year models of these machines and if parts are interchaneable, Thanks for any help.
  14. W

    Komatsu final drive noise

    I have a Komatsu PC128US 7 that has a whirring sound from 1 of the final drives, not a squeal and not a grinding sound, working as it should just has the whirring sound
  15. W

    M65 engine needed

    Sucked dust thru missing manifold plug and wiped out my engine, looking for used replacement,it is a buda d262 allis as best as I can tell
  16. W

    Fiat Allis M65

    I have an M65 diesel powered and have lost the plug out of the intake manifold, it is approx ! 1/4 in, does anyone have one laying around or have a part number for it,can't find it in my book
  17. W

    200 lc engine trouble

    The engine started smoking really bad suddenly,I have eliminated the turbo as the problem and removed the exaust manifold and smoke and small droplets of oil are coming from number 3 cylinder. I do not have a compression gauge to check the compression but the engine is not skipping and has very...
  18. W

    John Deere 200 Question

    Is the engine and pump on a John Deere 690 and a John Deere 200LC interchangeable, are any other parts on these machines interchangeable. Reason for asking is my 200LC engine took a dump and I can buy a 690 with a good engine for a good price.
  19. W

    Komatsu D31A-17

    I am in need of a left side axel and hub for this machine serial#32466 any help would be appreciated.
  20. W

    D37 final drive problem

    My d37 stopped pulling on the left track, when we pulled the cover off the sprocket hub we found that someone had welded the nut to the axel and hub, I assume the axel was stripped and this is how they repaired it, How expensive is it to replace the axel and hub. This is a good running and...
Top