• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. allen lafrance

    972 M Code E560 3 serial Cat0972MVL8E01222

    Hi everyone I have this code E560 and I dont have sis or troubleshooting manual but I find this leak in picture down…some one can help me to get troubleshooting on my issue ? Thanks a lot
  2. allen lafrance

    Case CX145D SR code

    Hi everyone I have this small excavator that was flooded I had to change the cabin connections and change two modules the one of the machine and the monitor I calibrated the monitor and I have these code there would you have a place where I could get out the diagnosis code list: 7014...
  3. allen lafrance

    Volvo G930 HVAC Blower never stop

    Hi I have a problem with my HVaC unit the blower never stop Some one have wiring diagram or location of resistance for the blower thanks #vce0G930T 00040105
  4. allen lafrance

    A25D code Ma2501-4

    Hi i have this code MA2501-4 some one can help me thanks
  5. allen lafrance

    D6K2 drive spocket tighten procedure

    Hi guys I need procedure for D6K2 the drive spocket thanks
  6. allen lafrance

    Volvo G946 How disassembly front wheel hub

    Hi I have a volvo G946 I need to change de oil seal in front hub I need help for precedure PN: 15403447 Thanks
  7. allen lafrance

    Volvo G946 Transmission Yoke out to differential

    Hi I have a G946 and the yoke output transmission leak but i see the yoke can move free like push in trans and u can pull like 1-2 cm out I have the gasket o ring and bolt tighten correcly thats normal or not the shaft dont move only the yoke Thanks for advise
  8. allen lafrance

    H16i code 235-341

    Hi everyone We have a hamm H16i and we have this code 235-341 when we use vibration the traction stop with yellow triangle can u help me with that Thanks all people
  9. allen lafrance

    H16i code 235-341

    Hello i have this code on Hamm H16I code 235-341 When i apply vibro traction stop stop with yellow triangle in display thanks
  10. allen lafrance

    A25D procedure for wheel hub seal change

    Hi everyone I have A25D the wheel hub seal leak and i need to replace him what the correct procedure bolt torque etc Thanks a lot
  11. allen lafrance

    Hamm 3307 Need some help to get Wiring Diagram and hydraulic

    Hi every one I have Hamm 3307 and i need diagnostic some things on this Some help to get wiring diagram and Hydraulic ur help Would be appreciated Thanks
  12. allen lafrance

    Cat 420 07A code 5551-2

    Hi I have this code some one have troubleshooting list for this code? Thanks
  13. allen lafrance

    Blue Bird Bus Isc 8.3? (Caps fuel pump)wont start

    Hi I need some technical info for my Blue bird bus 2004 with ISC cummins I have the possibility to have a diagnostic software I look for the diagnostic connector but I do not see it in the cabin of the Bus Crank no start no smoke the feed pump work filter ok I have fuel to my Fuel pump If u can...
  14. allen lafrance

    L70G

    when I bring the bucket towards me or vice versa the machine stops the rpm goes down and ends up dying what should I watch preasure port and spec ?! when raising it does not thanks
  15. allen lafrance

    Best wheel loaders

    Hi we look for new loader we need same capacity of Volvo L90g hard operation conditions what is the best Cat Komastu etc what’s is the beast
  16. allen lafrance

    L70G Transmission failure

    Need your opinion on the broken shaft 1-2
  17. allen lafrance

    Cat VC 60 SA Steering cylinder and knuckel Diagrams

    Hi Someone could have Part diagram of the rear axle cat VC 60 SA PLS Thanks
  18. allen lafrance

    cat 930G Bad pump maybe!???

    Hello we have repaired our cat 930g with cat tech we changed the hydraulic pump because the standby pressure fluctuates after having everything reconnected no pressure to the pilot line except when cap the return line of the orbitrol the bucket does not lift does not tilt The Cat technician says...
  19. allen lafrance

    Cat 930g P1 pressure

    Hi guys What is the pressure of P1 at idle slow lifting problem tilt slowly too
  20. allen lafrance

    CAT 930 G fan&brake pump assembly

    Hi I need the diagram of Fan & brake Pump(aux.pump) to rebuild it pls thanks
Top