• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. G

    Deere CT332 - No Hydraulics after changing wheel speed sensor

    I recently replaced the left side drive motor on my 2009 Deere CT332. Hooked everything up except the wheel speed sensor which was misplaced. Machine turned on fine but wouldn't operate as it threw a code for the missing wheel speed sensor. I ordered and installed the new wheel speed sensor...
  2. G

    CT332 with Drive Motor Problem

    Hello, I have a 2009 Deere CT332 with 2,400 hours on it. I know the drive motors are typically failing around this number of hours. The other day I noticed a burnt oil smell and stopped the machine and found leaking oil on the left side motor. See the attached pic... My question is whether...
  3. G

    Broken wire for CT332 Quick-Tach- Need help finding fuse???

    So I went to switch attachments using my 2008 John Deere Ct332. The electric Quick -Tach wouldn't move. I checked the wiring and found several sections that were damaged. I am fine with splicing them back together but was wondering if anyone knows where to find the fuse for the Quick-Tach? I...
  4. G

    How to replace the wheel speed sensor on a Deere CT332?

    I need to replace the wheel speed sensor on a 09 John Deere CT332. Can't find much information in the Technical manual. Do I need to remove the Track and Drive motor to get to the sensor? Thanks, Gumper
  5. G

    My Deere CT332 Stops moving after a few seconds?

    Hi Guys, Could use some help. I have a 09 John Deere CT332 with about 1,800 hours. Went to start it and it runs fine until I start to move it and then for some reason the electronics stop the machine from moving and I get an error code for the left track speed sensor? the code is HCU...
  6. G

    Wiring a 6 way dozer blade to a JDCT332

    Hi All. Just bought a 6 way blade and will need to connect it to my John Deere CT332. I do not have a 12 pin harness. Can I just wire it direct to the buttons on the handle somehow? Thanks for any advice. Gumper
  7. G

    Switching to cat control pattern on a Hundai 140 LCD ?

    Hi All, I have a 2008 Hundai 140 LCD that came from the factory with deere controls. My new operator is a cat guy so I need to change the pattern. There is no switch so I am hoping to move the hoses. Can anyone help? Thanks!
  8. G

    Brakes not releasing on a 2004 JLG450-SII

    Hi All, I have a JLG450-SII (2 wheel drive) which has an intermittent problem with the brakes not releasing. When I push the control to move, the pump spins up and I can tell the motors are trying to drive the wheels but the brakes wont release. Occasionally they do release for a brief...
  9. G

    Need some help estimating a large clearing job please

    Hi All, I've been asked to bid on a large clearing project. It's in excess of 40 acres mostly hardwood and I would need to fell all trees, chip on site ,remove the stumps and truck offsite. I was wondering if anyone has an idea of what a fair market cost estimate per acre would be for...
  10. G

    Need recommended source for auxiliary hydraulics please

    Hey all, I'm looking to add aux. hydraulics to my 2007 Hundai H-140 so I can add a Hydraulic thumb. Was wondering if anyone had a recommendation for an aftermarket supplier? Thanks. Gumper
  11. G

    Hyundai H-140 with low RPM's and stall problem

    I have a 2009 Hyundai H-140 with only about 280 hours on it. Recently, the RPMs will fluctuate and then the engine stalls....it starts right back up and idles fine and then as soon as I track the machine or operate the stick, it seems like it struggles and barely runs. All the fluids have...
  12. G

    Need some advice on welding a manual thumb to an excavator stick

    I just recieved my new Bodine mechanical thumb and am going to weld it to my Hundai H-140 I will be using a stick machine with 7018 rod. Any tips or suggestions? I do know to disconnect the batteries and place the ground near to the weld area. Thanks for any help!
  13. G

    JLG450A SII, bucket rotates freely

    I have a 2004 JLG 450A II with about 800 hours on it. I mistakenly bumped the bucket against my truck when the bucket was turned all the way to the side. (parallel to the machine) Now the controls to turn the bucket don't have any effect and the bucket just swings freely. Is there some kind of...
  14. G

    difficulty with flat faced connectors

    Hi All, I have a 2009 Deere ct332. Every so often I have a hard time getting the flat faced connectors to connect. I assume it's because of excess pressure in the lines? Sometimes I can crack the fitting on the attachement and draina little oil out and it seems to help. Is there any...
  15. G

    Error code on JD CT332

    I keep getting an error code which reads 2392.05 ECU. I looked through my manual but can't find any details of the error codes. Anybody know what this means...It's an 09 machine with only 50 ish hours or so..... Thanks.
  16. G

    Will this truck be big enough?

    My buddy has a 05 GMC 8500 dump. It has a 20 ton pintle and airbrakes w/air hook-up for the trailer. The GVWR is listed as 52,000 lbs. There is no listed cGVWR. I want to use it to haul my 33,000lb. Hundai H-140 excavator on a 20 ton tag with air brakes. The motor is a 300HP cat with...
  17. G

    Hose Routing Question

    I bought a slightly used Bobcat HB980 hammer at an auction. Took the hoses of to repaint it and you guessed it.....forgot to mark which was which.... Does anybody know if the orientation of the hoses matters? Thanks for the help.
  18. G

    tips for testing used Hydraulic Breaker?

    Just bought a used Bobcat HB980 Hydraulic Breaker at an online auction. Anybody have any tips on how to tell if it is working efficiently....or if it needs a rebuild? It was a rental unit so I'm sure it was treated with love and tenderness....:D
Top