• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. G

    Deere CT332 - No Hydraulics after changing wheel speed sensor

    It has oil. Is there a trick to clearing the stored codes? There are no active codes but there are 8 stored codes. If I disconnect the battery for a few minutes would that clear the computer? Thanks!
  2. G

    Deere CT332 - No Hydraulics after changing wheel speed sensor

    I recently replaced the left side drive motor on my 2009 Deere CT332. Hooked everything up except the wheel speed sensor which was misplaced. Machine turned on fine but wouldn't operate as it threw a code for the missing wheel speed sensor. I ordered and installed the new wheel speed sensor...
  3. G

    CT332 with Drive Motor Problem

    I finally found time to look into this....used the slide hammer trick to remove the front cover (worked great). I welded the center plug right onto the end of one of the slide hammer attachments. 2 pulls and it was off. At first glance it didn't look too bad, but once I cleaned out the oil...
  4. G

    CT332 with Drive Motor Problem

    I managed to get the snap ring off pretty easily. I'll need a new one for obvious reasons... Ordered a new o-ring and snap ring. I hit it with some PB blaster and gonna let it soak overnight. Definitely has some rust but not too bad...didn't have to worry about draining the oil cause there...
  5. G

    CT332 with Drive Motor Problem

    Thanks very much for the info. I looked at the parts drawing and it shows a O ring and also a snap ring? I am going to make a adapter to use with a slide hammer too...seems like it will be the best way Can this be done with the track still on and the motor/gearbox on the machine? Is it just...
  6. G

    CT332 with Drive Motor Problem

    Hello, I have a 2009 Deere CT332 with 2,400 hours on it. I know the drive motors are typically failing around this number of hours. The other day I noticed a burnt oil smell and stopped the machine and found leaking oil on the left side motor. See the attached pic... My question is whether...
  7. G

    Broken wire for CT332 Quick-Tach- Need help finding fuse???

    It was a bad fuse. Thanks very much for the help. I appreciate it.
  8. G

    Broken wire for CT332 Quick-Tach- Need help finding fuse???

    So I went to switch attachments using my 2008 John Deere Ct332. The electric Quick -Tach wouldn't move. I checked the wiring and found several sections that were damaged. I am fine with splicing them back together but was wondering if anyone knows where to find the fuse for the Quick-Tach? I...
  9. G

    How to replace the wheel speed sensor on a Deere CT332?

    There are 2 active and a few stored. The active ones are 2661.14 (Right Joystick, Y-axis) and 2698.14 (Left Joystick, Y-Axis) The Stored are 190.12 (Engine Speed Sensor), 1594.02 (Left Speed Sensor Input), 2698.14 (Left Joystick, Y-Axis), and 2392.05 (backup alarm) I wonder if maybe there is...
  10. G

    How to replace the wheel speed sensor on a Deere CT332?

    I finally got some time to replace the sensor. It went well, but I'm still getting the same error code (says bad data) and the computer shuts down the tracks from moving. Is there something I have to do to clear the codes? Thanks for the help. Gumper
  11. G

    How to replace the wheel speed sensor on a Deere CT332?

    Great, thanks for the info. Do you know if I will have to do any kind of calibration once it is installed? Thanks, Gumper
  12. G

    How to replace the wheel speed sensor on a Deere CT332?

    I need to replace the wheel speed sensor on a 09 John Deere CT332. Can't find much information in the Technical manual. Do I need to remove the Track and Drive motor to get to the sensor? Thanks, Gumper
  13. G

    My Deere CT332 Stops moving after a few seconds?

    Hi Guys, Could use some help. I have a 09 John Deere CT332 with about 1,800 hours. Went to start it and it runs fine until I start to move it and then for some reason the electronics stop the machine from moving and I get an error code for the left track speed sensor? the code is HCU...
  14. G

    Wiring a 6 way dozer blade to a JDCT332

    Hi All. Just bought a 6 way blade and will need to connect it to my John Deere CT332. I do not have a 12 pin harness. Can I just wire it direct to the buttons on the handle somehow? Thanks for any advice. Gumper
  15. G

    Switching to cat control pattern on a Hundai 140 LCD ?

    Uffex, Thanks very much for this link. It was very helpful. Gumper
  16. G

    Switching to cat control pattern on a Hundai 140 LCD ?

    Here's a picture of the valve block. I assume I have to switch two of these hoses around?
  17. G

    Switching to cat control pattern on a Hundai 140 LCD ?

    Hi All, I have a 2008 Hundai 140 LCD that came from the factory with deere controls. My new operator is a cat guy so I need to change the pattern. There is no switch so I am hoping to move the hoses. Can anyone help? Thanks!
  18. G

    Brakes not releasing on a 2004 JLG450-SII

    Hi All, I have a JLG450-SII (2 wheel drive) which has an intermittent problem with the brakes not releasing. When I push the control to move, the pump spins up and I can tell the motors are trying to drive the wheels but the brakes wont release. Occasionally they do release for a brief...
  19. G

    Need some help estimating a large clearing job please

    Thanks for the responses guys...I was thinking 4K was the right number as well.
  20. G

    Need some help estimating a large clearing job please

    Hi All, I've been asked to bid on a large clearing project. It's in excess of 40 acres mostly hardwood and I would need to fell all trees, chip on site ,remove the stumps and truck offsite. I was wondering if anyone has an idea of what a fair market cost estimate per acre would be for...
Top