• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. texaschad25

    939C electrical issue

    Ok Thanks Don. I've hunted high and low in both places and couldn't find one in either place. I'll try again tomorrow.
  2. texaschad25

    939C electrical issue

    I knew I was leaving something out. Thanks Nige! Serial: CAT0939CC6DS01253
  3. texaschad25

    939C electrical issue

    While installing a new radio antenna, I dropped a small socket into the cigarette lighter plug. I had the key on and immediately noticed that I lost the radio. I've also lost power to both wipers, AC fan, and dome light. I've also noticed that after I start the loader, the red (lightning bolt)...
  4. texaschad25

    Transmission temp gauge on D7E

    Ok thanks!
  5. texaschad25

    Transmission temp gauge on D7E

    Ok thanks David. Is it easiest reached from the top or bottom? Thanks again!
  6. texaschad25

    Transmission temp gauge on D7E

    I'm replacing the transmission temp gauge on my D7E high horse. I pulled the floor pans and the old gauge line has been cut off under the pans. Can someone tell me where the probe screws into the trans? I don't want to take off any more stuff than I have to. Thanks for the help.
  7. texaschad25

    D7E 48A compression release

    It's 24 volt, and I don't see aby thing coming out of the dash. I will look closer when I go down there later today. After the starter is rebuilt, it will spin and crank as normal. After several months, it will start lagging like it's a low voltage issue, but the batteries are hot. Since...
  8. texaschad25

    D7E 48A compression release

    My D7E 48A seems to be going thru starters at a pretty fast rate, and I was asked if it has a compression release. Can anyone answer this for me, and if so, where in the heck is it located? It has the pony motor replacement starer. Thanks!
  9. texaschad25

    D7E 48A starter issue

    I'll have to look and see what starter it is. I'll also check into the voltage issue.
  10. texaschad25

    D7E 48A starter issue

    I've had the starter on my 7E rebuilt 3 times over the past 2 years. After coming out of the shop, it will start fine for several months, then the starter will delay before spinning over. Once I hit the button, I can hear the relay, then it may take 1 second or it may take 3 or 4 seconds before...
  11. texaschad25

    68 D7E engine screens

    Did you get them from Kenco?
  12. texaschad25

    68 D7E engine screens

    I called about a year ago and they were $1200. I may wind up taking you up on the offer Don. I owe you lunch for your help with my injectors!
  13. texaschad25

    68 D7E engine screens

    I'm looking for a set of engine screens for my 68 D7E 48A with the D339. Thanks.
  14. texaschad25

    D7E 48a injector issue

    Thanks for the help Don! I had 2 of them off by 1 tooth, and one was off by 2 teeth. Slapped it back together and it's running like a wildcat!! Thanks again!
  15. texaschad25

    A D9G Follwed me home today "Ex Mashuda" machine

    That 9 makes my old 7E look like a kids toy. Enjoy it!
  16. texaschad25

    D7E 48a injector issue

    That's exactly what I was talking about, Don. Thanks for your help!
  17. texaschad25

    D7E 48a injector issue

    A few weeks ago, I had 2 O rings leaking between the pump and two of the lines, so I decided to replace all of them. When I pulled the cap housings from pump, each individual nozzle came out with the cap. I replaced the orings, but I apparently don't have the nozzles set correctly. The dozer...
  18. texaschad25

    D7E brake bands

    Screen and magnets
  19. texaschad25

    D7E brake bands

    It did come out in one piece but we had to split the screen to get the magnets out. That thing was a booger to get out of the dozer. Pry-tap, pry-tap, yank... wouldn't be surprised if it's never been out. We ordered a new screen from Cat and it will be here tomorrow. Where is the screen for the...
  20. texaschad25

    D7E brake bands

    I think we found the issue..
Top