• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. J

    Waedoo g30s propane

    I have a waedoo forklift on the number 2 and 3 piston there is only 50 lbs compression, 1 and 4 have 135 ,no blowby, nothing blowing out the radiator,can't hear any funny sounds any help much appreciated.
  2. J

    Allison tt series transmission issue

    You will understand more once you take the transmission apart you only need to remove input shaft cover
  3. J

    Allison tt series transmission issue

    If there's only slow speeds that means that the first turbine is doing its job. For higher speeds the torque must be low ,the freewheel clutch is geared much higher ,it than starts to grab hold of the second turbine shaft witch in your case is missing so there will only be one speed This is a...
  4. J

    Allison tt series transmission issue

    You need to remove the transmission. the shaft that is damaged drives the freewheel clutch which i think is locked up,the first stage turbine was fighting with the second stage turbine that caused the splines to strip.being the freewheel clutch locked up. If I were you I buy a rebuild...
  5. J

    Cat C7 No Go--Flat won't run--Help troubleshooting please

    Had the problem with a c9.replaceed the heui . Wasn't the problem The wire from ecm to heui pump was bad.
  6. J

    JD Tractor 2950 6359 cu timing help

    Had the same issue with a 6404 jd The cam bearing were bad and at some point seized the cam and stripped the half moon key in the drive gear when the key stripped it locked in at a different position took I while to find that out
  7. J

    JD 244J Wheel Loader - Long Beep - locks up transmission

    Had the same happening to my jd323e track loader problem was with the speed sensors.
  8. J

    Random thoughts

    All I've every done was two glow plugs , fan belt pulleys. front wheel bearing hubs,haven't touched the power train,two repaint , body work.
  9. J

    Random thoughts

    Got an 08 duramax 472k haven't touched the motor yet.
  10. J

    Wheel Loader advice

    Do you mean(new) to you?
  11. J

    Gradall for sale

    Motor not firing on one Piston Been sitting for 5 years
  12. J

    Looking for recomendations. 2 way radios

    The cheaper the better because they get dropped that's bad for them What more important is the band Get UHF the highest frequency number they came get you.
  13. J

    MF 50a alternator replacment and wiring guidelines

    I think the confusion comes from the generator and the alternator. You have the drawings for both, you need to decide which one you want to use. The generator needs a voltage regulator. The alternator does not. The simplest to make work is the GM alternator.
  14. J

    MF 50a alternator replacment and wiring guidelines

    I was taking this guy apart to remove the engine which had a bent crank I like to take pictures when t take stuff apart be I find the older I get the more I forget
  15. J

    MF 50a alternator replacment and wiring guidelines

    Black wire comes from ignition
  16. J

    Bobcat T770. Mowing pine rows, climbing stumps and hills tracks keep coming off

    Had the same problem with a john deere 323e no sign of anything wrong with the tracks replace the tracks problem disappear ,
  17. J

    Case W20C engine installation

    Had a similar problem with a john deere where the flywheel was catching on the starter turned out be a bent crankshaft and worped block $$$$
  18. J

    Case W20C engine installation

    Is this the original engine you are installing?
  19. J

    Eco block forms

    https://www.foxblocks.com/ Built a few houses with these won't use anything else
  20. J

    Case W20C engine installation

    Some of these loaders did not use a flex plate you may have the wrong bell housing.
Top