• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. Wastepro

    930G Sputtering and Cutting Off

    No but I did try running it without the fuel cap with no luck.
  2. Wastepro

    930G Sputtering and Cutting Off

    We didn't drain the tank from the bottom, will do so today. We pulled the pickup to inspect the tank visually and blow out the pickup lines because I was concerned that a piece of debris was floating in the tank and clogging the lines periodically just like you suggested. Doesn't seem to...
  3. Wastepro

    930G Sputtering and Cutting Off

    Haven't come across any screens yet, but I haven't been looking for them. All the rubber lines we replaced just slide on with clamp so no banjo fittings have been pulled. I'm gonna check the filter housing connections like Jonas 302 suggested and I think they are steel lines with fittings so...
  4. Wastepro

    930G Sputtering and Cutting Off

    Have a 930G here seriel number TWR She fires right up every time no problem. However intermittently she likes to sputter and/or cutoff. Could be 1 time per hour or 10. Throttle can be any position, bucket can be any position, at idle or while running hard. Seems like it sputters more...
  5. Wastepro

    DEF Delight or not??

    Does anyone have a good lead on where to get help with the delete. working on a 2011 Case puma tractor with the 6.7 engine. Tractor has complete SCR failure right now and wont stay running long enough to pull it out of the tractor shed and get any work done. Thanks yall.
  6. Wastepro

    Poly Cutting Edge

    it might be worth mentioned that we rarely move dirt. Most material used by our buckets are loose organics. Currently been fine with metal cutting edge but we are careful working on the concrete. Very curious about the poly edge because we could clean and clear the concrete pad bettter between...
  7. Wastepro

    Poly Cutting Edge

    Anyone ever used a poly cutting edge for working a loader on concrete. We are needing the replace the cutting edge on our 9' bucket and was considering this option. Anyone had experience? Looks like we are $400+ for the poly edge or $850 for a new metal one from CAT. THanks for opinions...
  8. Wastepro

    DEF Delight or not??

    Gene, Did you ever get to the bottom of this? What was the bill like from the dealer? We have a 2011 Case Puma tractor that just started throwing the 3612 code and SCR failure> Checking around to see what people have done. Our warranty was up last year, lucky us
  9. Wastepro

    Starter stays engaged

    Tapped the solenoid real good with a hammer too see if would disengage. No luck so After that we pulled the starter and the bendex was stuck extended. Bad news since we had to give my left arm for a starter from Cat at $549.99. Just fired it up and everything is good to go. Thanks everyone...
  10. Wastepro

    Starter stays engaged

    Hey thanks to everyone suggestions. One small update to reply, I disconnected the small wire to the starter which comes from the starter relay. This made no change. The starter immediately tries to start the machine and stays engaged when the master electrical is cut on. So far I have...
  11. Wastepro

    Starter stays engaged

    Hey Ya'll, Hope everyone in the Southeast is enjoying the dry weather and able to get out and start making some. I've got a Cat It24 F Serial 4NN00391 The starter stays engaged after startup. If I cut the electric off at the master switch then the starter disengages and the diesel motor...
  12. Wastepro

    Low brake pressure Alarm IT-24

    Series number 4nn00391
  13. Wastepro

    Low brake pressure Alarm IT-24

    Low brake pressure alarm going off. Everything still works fine and doesnt go off until after running the machine for 1-2 hours. Any help would be appreciated, dont know where to start looking.
  14. Wastepro

    What to do if you found out a worker has behavioral issues?

    I draw the line at the money. Is he costing you money?=time=business. If the answer is Yes, hes got to go work somewhere else. Everybody has to be profitable for the business.
  15. Wastepro

    Anyone know about a Case MW24C?

    From the pictures it doesn’t look like the 2.5 yard bucket on there is removable. https://www.govdeals.com/index.cfm?fa=Main.Item&itemid=5&acctid=10992
  16. Wastepro

    Anyone know about a Case MW24C?

    Looking for some information on 1984 CASE MW24C We are looking for another loader to use mostly on hard surfaces stockpiling material weighing about 1000lbs/yard We have buckets now that fit a cat IT24. Will those buckets work on the case machine? Are these reliable machines? Any idea on...
  17. Wastepro

    Cat C7 ACERT

    we have a c7 acert in an 2005 Freightliner. Just getting to 275K miles and about 10,000 hours. No problems (yet) but I am waiting and have been told to expect them. People have told me to change oil at 5k intervals and keep the fuel clean (true of any engine) but that helps them avoid...
  18. Wastepro

    //// Overheated engine but dodged a bullet ?? /////

    Fire the girlfriend. Dump the employee. and Sell the truck. Problem solved. :D
  19. Wastepro

    Independent Start-Up Journey

    Nice work Jesse. Get up and early and surely you will be successful.
  20. Wastepro

    The Death wishers'

    Truck Shop knows what'sup. I would recommend anyone in the truck industry get a Dash Camera. As others are saying about how people drive. Don't think I can add anything here, its obvious a lot of people suck at life. We have dash cameras in all of our trucks. Got the wall mart Garmin...
Top