• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. O

    asv,rc85 paint

    Does anyone have the paint code,or asv part# for the 2005 yellow, on the RC85.Im wanting to do some touchup without a complete repaint.
  2. O

    D5C turbo issue (oil)

    My D5C started using oil about fifty hours after engine rebuild.About a quart an hour under hard use.Oil pressure is 70/75 engine has no blow by and runs perfect.Pulled the turbo and found oil in the compressor side,took it to the shop for a rebuild($500) still going through oil.Today I serviced...
  3. O

    Samsung 120-2 No steering,transmission,hydraulics

    Just purchased dead! Was told that everything worked @ shutdown on Friday,Monday morning started as normal but, No trans,no steer,no lift,all dead.Engine runs fine drive shaft to converter rotates.I have service and parts books on the way,but in the meantime looking at some pictures it looks...
  4. O

    Cat 910 steering

    My mid 70s vintage 910 steering doesn't work when cold (45/50 degrees) Can hardly turn the wheel,after running a few minutes,works perfect.Fluid is clean.I did see in the manual there is a valve of some sort under the floor by the master cylinder "flow control and relief valve" I'm thinking of...
  5. O

    TL26 Takeuchi

    TL26 op says working ok,backed up for a new cut stopped,no for or rev on left side.Right side goes a few inches for and rev but stops,and does not pull.Went over with loader to pull out of job site,tracks locked both sides.Questions are,does this model use a cable and pin sprocket brake? And is...
  6. O

    C frame Eye bolts stuck

    Rebuilding the blade on my D3B down to the Eye bolts at the rear of C frame,got the nuts off but cant get the eye bolt to budge.Put a pin in it and jacked the tractor up trying to twist it,no luck yet any thoughts?:Banghead
  7. O

    D3B blade ball question

    Replacing the the ball, and pillow blocks on the blade of my tractor.My question is,there is no grease up there, it is a dry joint. Sand and grit is free to fill the gap around the ball and work its way into the joint,only to be ground into grinding compound:confused:Has anyone ever put a thick...
  8. O

    Making blade pins?

    I'm rebuilding the front of my D3b. My question is looks like I will need most if not all new pins,in the angle,tilt,lift ect.Priceing them,they are around $40 each.They are 1.500 dia.Is there a grade of steel round stock that I can make them from.Some of the polished and ground stuff looks...
  9. O

    Heat or no heat

    Going to rebuild all front hydraulics on my D3b,borrowed a huge chain wrench with a 5' handle,I weigh 200 and my son 200 we have added a three foot Cheater and the crowns won't budge.There were no set screws.Next step is maybe a little heat,what do you all think.As near as I can figure we have...
  10. O

    loose yoke on cat

    Trying to clear up the last of the oil leaks on on the Caty 936F. It looks like there is a leak at the rear drive shaft yoke,where it slides into the rear differential.I know there is a seal there, but the yoke is a little sloppy,up and down on the pinion shaft.I know this is not normal,but is...
  11. O

    Cat 936F brake fault light

    Just purchased this loader knowing it had no brakes,#8AJ01502,I was pretty sure I knew what was wrong,and so far so good.The peddles were froze solid.The pivot,rollers,and plunger were all a big ball of corrosion.and one air valve had a big groove under the o ring.So two new air valves,peddles...
  12. O

    Cat 936F drift

    Just purchased this loader #8AJ01502 and trying to get her into shape.But now, I find the machine will not hold itself up.All functions work normal,except the down pressure hold.You can fill the bucket,let it sit over night and it will drift only a couple of inches.But if you lift the front...
  13. O

    Cat 936F won't shut down

    This loader is new to me.It will only shut down by lifting up on the accelerator peddle.Is this normal.Seems as though the key should shut it down.I now have the service manual for it and cannot find and reference to a fuel shutdown solenoid.Nothing shows up in the injection pump section ether.
  14. O

    Cat 936F no brakes

    Just bought a 936F,very clean strait loader serial# 8AJXXXXX problem is both brake pedals are frozen solid,no movement at all.Looks like the brake linings are in the differentials.All fluids are very clean and no burnt smell.The brake fault light is on.My question is are the brake treadle valves...
  15. O

    Case 1845C weak right side

    My sons Case 1845C has got the right side drive that will no longer pull itself,other than in a strait line.Has no power for pushing or turning.would the problem most likely be drive motor,pump,or both.it has got bad over a period of time.left side seems ok!
  16. O

    D3B right brake locked this morning

    This machine has thirty five hours,on new clutches and brake bands.It is a 1983 D3B.My operator just called and said the right side brake is locked.It has been working perfect,25 hours ago we set the bottom bolt to 1-1/2 turns from snug and top ajuster is 1-1/2 to 2 turns from snug.That was 25...
  17. O

    Tach don't work!

    I just picked up a very nice 91 L9000 tipper with a L10 cummins,the tach don't work.It does not seem to be cable driven.Can someone tell me where it picks up the signal from.Thanks
  18. O

    D3b bottom rollers

    Just got a new undercarriage for my tractor.1983 D3B Im wondering if the bottom rollers use just bolts,or nuts and bolts to attach to the frame,I can't tell because of the rock guards.Im worried about them breaking off in the frame.Whats the best way to get the rollers off.Also the new sprockets...
  19. O

    Case 450 rattle

    Got a 77 450 case that I've had for about six years.When I bought it there was a rattle that sounded like the converter bolts were loose,so we pulled the converter out there are no bolts.It drives the converter with a fibre tooth ring gear.It was worn and loose so I bought a new one,put it back...
  20. O

    D3 decelerator

    Help! Got a 83 D3B I would like to put a decelerator on it.Does any one know if Cat makes a kit,or would anyone have a picture of how it works so i could build one? Thanks
Top