• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. LogDog

    Link Belt 5800 c-series 2 computer repair.

    Hello I have a 5800 link belt, the computer has gone bad. Is there any recommendations for a repair shop for the device? Thanks Roger
  2. LogDog

    link belt 5800c series 2 parts needed

    Have a 5800 machine ,I am looking for a cab door and upper and lower front windows with frame, picture is of machine , I believe that other size machines used same setup. Thanks Roger WASH. State.
  3. LogDog

    ls5800c2 link belt help to id a new to me machine

    john. it is an excavator, has a short stick, double bar grousers (narrow) thumb and cab guarding. pretty tight old machine. will work good for me.
  4. LogDog

    ls5800c2 link belt help to id a new to me machine

    I Recently bought a 5800 link belt the serial number is lc612-470 it has a Izusa motor. seems to have had an electrical issue as throttle and stop engine control are done with some industrial type manual cables. As the dash area (display) is non functioning was wondering what would the...
  5. LogDog

    cat v120

    Looking to transport a cat v120 forklift, it is 12 ft. tall with mast tilted, Is it possible to disconnect cylinders to tilt mast further forward for transport. thanks.
  6. LogDog

    580k torque converter Acess.

    Working on my first series 580k. is there an easier way to access the converter-flexplate bolts better than thru the starter hole?
  7. LogDog

    140h water in transmision

    Randy I am 30 miles west of Olympia, Near McCleary. yes was an easy fix, glad to have it back online. thanks agian Roger
  8. LogDog

    140h water in transmision

    Problem solved! got machine in and cleaned up, removed fuel tanks nothing visible. Removed trans breather, and plugged in 10lbs of air and immediatly heard it leaking. turned out it was at the dipstick/fill tube, found a 3/8 flat washer between flange and housing leaving a gap don't know but...
  9. LogDog

    140h water in transmision

    good morning randy yes my post was unclear, we use the red long life anti freeze, the trans oil is not discolored a redish tint which would indicate coolant in system. first suspect one would think is trans cooler, but oil pressure is higher than water pressure ie nothing in radiator...
  10. LogDog

    140h water in transmision

    140H APM00666. Am getting fresh water, not coolant in trans oil. Trans oil level consistant,no loss of coolant, also no color in oil ,or sweat in fill tube. machine did have a small oil spot near lower pivot after roading 10 miles. My theory is its a low pressure thing . ie ring gear slings...
  11. LogDog

    140H Electrical

    smoothoperator thanks, recently purchased, and wanted to add more lights, wireing is there, and parts book gets you close. thanks
  12. LogDog

    140H Electrical

    Looking for electrical diagram for 140H serial#apm00666. Dealer say we have to buy complete service manual?. thanks
  13. LogDog

    Any good stories about the Brooklyn Tavern?

    I have Hauled for arnie before,some out at pacific beach. then in the summer over at cle ellum when Mike drove there truck trip for trip with everyone else, but did it with only use of his left arm! (try that sometime) I remember vaguely back in the day they had a long hood kw with a v12...
  14. LogDog

    Grading the Mainline

    Thal? ya caught me. Where did you get enough sunshine to take those photos Had snow again this morning. been wet here as well,
  15. LogDog

    Grading the Mainline

    few more misc. from our area,building a crown on lund a-line, ripping/scarifiying potholes upper wishkah, grader parked in front of the "million dollar cut" on rayonier 3200 line, story is that what it cost to build for the railroad back in the day. moving day with the new lowboy tractor...
  16. LogDog

    Because of this site

    akroadrunner Having lived on the harbor all my life was curious if you are related to steve or Rick Ross that live around copalis crossing? also there was a Ross that logged in late 80s or so that had blue mack trucks with super single tires? Roger Landberg
  17. LogDog

    Highway log trucks.

    my old 77 Mack, 375 V8, was fun then but looking back it was alot of work,
  18. LogDog

    Grading the Mainline

    Thought I would post a pic of some grading pics in the woods. this is the first pass on a new to us 2005 140H, shown on Bishop A-line in Pacific County,Wash.on former weyco ground that recently sold to hancock. machine is a very big improvment over our older 140 which I thought was pretty good!
  19. LogDog

    330B meltdown

    Hey all heres a few pics of the 330b I was running friday when it caught fire, was moving a few logs closer to the road so the self loader could reach them smelled something and saw smoke out to the right, looked over shoulder to see flames comeing through the Hood. shut er off and grab...
  20. LogDog

    wind turbine project

    some pics of a wind turbine project in Grayland wa. 16 ft diameter hole 31 feet deep. dug starting with 345 to about 18 fet or so, then use 330 with long boom and stick to spoon out remaining. have a topman directing my movements. tube in background is outer ring they will place a smaller...
Top