• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. T

    Snorkel TB 60 turn table issue.

    I have a Snorkel TB60, Ser # JA01089 . The turntable won't function from the platform joystick control. Turntable works as it should from the ground control. Upon inspection there are 2 microswitches and a potetionometer under the joystick control. Is there a procedure to test the...
  2. T

    Rayco C85D 2 speed issue

    I have a 2002 Rayco C85D mini crawler that doesn't go into transport speed. The wiring diagram shows the current flow from the switch up to the overhead computer control , then down to the solenoid control valve on the hyd block. I have power going into the computer and nothing coming out. My...
  3. T

    Allis Chalmers 653 Dozer parts

    My customer has a low hours 653 dozer and is looking for origional ammeter, water temp and oil temp gauges. Any one have a parts book with correct part numbers, so that I can look online or know of a vendor that would have access to them. They are all electric gauges. Thanks, Terry
  4. T

    Hough H60-B seal

    Does anyone have a parts book for a Hough H60B wheel loader, 343-311U, Ser # 01274 ? I would like to the part number for a rear axle wheel seal. F P Smith equip. didn't seem to be of any help without a part number. Does anyone know of any other places that might carry this seal. It is way...
  5. T

    Vermeer LM42 trencher

    I have a Vermeer LM42 trencher with a damaged traction pump. Vermeer distributor says there is a 4 + month wait and no individual repair parts available. The pump part # is 223978001 2 speed pump.Is there anything after market for this? There is no identification on the housing. Does anyone know...
  6. T

    Hough H60-B radiator

    Does anyone have a parts book for an antique Hough H60B wheel loader, ser # 01274 ? I am looking for the part number for the radiator with an International D301 diesel engine. Thanks, Terry
  7. T

    Thomas 133S electrical problem

    I have a Thomas 133 skid steer, model A502133S; SER # LE006664. This a later ser # machine and everything is a lot different than the 133 parts book on the Thomas website. Anyone have an electrical wiring diagram they can email me? I am having an issue with the loader control valve lockout...
  8. T

    Bent fork on farm loader

    I have a fork off a Massey Ferguson farm loader. I t is tweaked about 1/2 to 5/8" 5" from fork upright. The fork measures 4 3/4" wide X 1 1/4" thick. Anyone have experience or luck in straightening forks.
  9. T

    TB45 bottom roller

    I have an old Takeuchi TB 45 excavator 1988 vintage with steel tracks. I am looking for a bottom roller. I haven't had any look doing web search. Found some for a TB045 but had a disclaimer that it would not the TB45. Takeuchi part # 02113-90000. Any ideas where to look? Thanks, Terry Z
  10. T

    case 580ck forklift

    I have an old case 580 constuction king with a harlo forklift mast. I am having trouble finding the correct manual shuttle input gear-shaft assembly. The case parts book shows a part # of A37617. The teeth on the gear are the same ; the bearing land & snap ring groove are the same. The gear...
  11. T

    deutz BF4m1011F parts book

    I am looking for a parts book for a Deutz BF4m1011F, SER # 263545. I have aGehl parts book but Gehl uses their own part numbers. There are some aftermarket parts available but I need Deutz part numbers to reference them. Genuine Deutz parts are priced like they are gold plated.
  12. T

    Deutz Bf4M1011f

    I have Deutz BF4M1011F engine that I need to find the heigth of the pistons above the block. The Deutz manual calls for a special service tool to set up and measure the height to get the right head gasket; one of three. Anyone have the poorman's tools, a straight edge and feeler gauge to get a...
  13. T

    terex tc50 hydraulic problem

    I have Terex TC50 excavator, ser # 0219. machine operates & works good for 15 - 20 minutes until oil warms up to operating temp. It then starts to slow down operating speed and will quit operating or track motion. It acts like the pump is deadheading as it will drag the engine rpm's to a stall...
  14. T

    terex tc50 hydraulic problem

    Customer has a Terex TC50 excavator, ser # 0219. machine operates & fine for 15 - 20 minutes until oil warms up to operating temp. it then starts to slow operating speed until it quits operating or moving tracks. It acts like the pump is deadheading as it will drag engine rpm's down to a stall...
  15. T

    oil capacity case 1845c

    Anyone know the chaincase oil capacity of a case 1845c? the machine came into our shop with the cases drained. I don't see any level plugs. Thanks, Terry
  16. T

    bandit knife clearance

    Anyone out there know what the anvil to disc knife clearance is for a Bandit 250 disc chipper? Terry
  17. T

    Twin Disc clutch parts

    I have a Bandit 250 chipper with a Twin Disc SP11P301 clutch that pretty well trashed. Any aftermarket parts available for these clutches? Thanks, Terry
  18. T

    Gehl 6635 brake parts

    Looking for aftermarket parking brake disc kit, Gehl part # 132636. Gehl wants $567.00 which is a lot of money for what it is. thanks, Terry
  19. T

    Gehl 6635 hydostat pump controller

    I have a Gehl 6635 that won't hold neutral; the hole in the flat steel arm and the pin it pivots on in the controller assembly is worn, allowing right side wheels to creep in neutral if the operator doesn't keep holding it neutral. This is an early series 1 machine; dealer wants $840.00 dollars...
  20. T

    Bobcat 773 G series

    I have a Bobcat 773 G, ser # 519013216. machine was in the shop for a traction lock problem; fixed traction lock problem, after sitting for 2 weeks waiting for parts started machine up to remove safety bar to leave shop have no lift or tilt function. turn key on, ach lite comes on; lift and...
Top