• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. T

    Snorkel TB 60 turn table issue.

    I am not familiar with with these types of control systems. Do you have a wiring diagram for this circuit ? I don't know which wires represent B,x,a. Thanks for the reply, Terry
  2. T

    Snorkel TB 60 turn table issue.

    I have a Snorkel TB60, Ser # JA01089 . The turntable won't function from the platform joystick control. Turntable works as it should from the ground control. Upon inspection there are 2 microswitches and a potetionometer under the joystick control. Is there a procedure to test the...
  3. T

    Rayco C85D 2 speed issue

    Thanks for the info, works ok now.
  4. T

    Rayco C85D 2 speed issue

    I have a 2002 Rayco C85D mini crawler that doesn't go into transport speed. The wiring diagram shows the current flow from the switch up to the overhead computer control , then down to the solenoid control valve on the hyd block. I have power going into the computer and nothing coming out. My...
  5. T

    Allis Chalmers 653 Dozer parts

    My customer has a low hours 653 dozer and is looking for origional ammeter, water temp and oil temp gauges. Any one have a parts book with correct part numbers, so that I can look online or know of a vendor that would have access to them. They are all electric gauges. Thanks, Terry
  6. T

    Vermeer LM42 trencher

    Yes we did. The owner decided to repair with new Vermeer parts. Expensive though.
  7. T

    Hough H60-B seal

    There were no numbers on the seal. I did find the seal at Thill Track & Tractor in Wisc. The Hough part number is 157078H3. Thanks for the reply.
  8. T

    Hough H60-B seal

    Does anyone have a parts book for a Hough H60B wheel loader, 343-311U, Ser # 01274 ? I would like to the part number for a rear axle wheel seal. F P Smith equip. didn't seem to be of any help without a part number. Does anyone know of any other places that might carry this seal. It is way...
  9. T

    Gland nut won't budge on top of cylinder - I read about peening. But....

    These type cyls, can be a real bear to get apart if there is no oring above the threads to seal the threads from contamination. An air chisel with a 1" hammer head works good by hammering around the cyl. barrel at the threaded portion, get on it with your 4' pipe wrench and an extension if...
  10. T

    Vermeer LM42 trencher

    I have a Vermeer LM42 trencher with a damaged traction pump. Vermeer distributor says there is a 4 + month wait and no individual repair parts available. The pump part # is 223978001 2 speed pump.Is there anything after market for this? There is no identification on the housing. Does anyone know...
  11. T

    Hough H60-B radiator

    Does anyone have a parts book for an antique Hough H60B wheel loader, ser # 01274 ? I am looking for the part number for the radiator with an International D301 diesel engine. Thanks, Terry
  12. T

    Thomas 133S electrical problem

    I have a Thomas 133 skid steer, model A502133S; SER # LE006664. This a later ser # machine and everything is a lot different than the 133 parts book on the Thomas website. Anyone have an electrical wiring diagram they can email me? I am having an issue with the loader control valve lockout...
  13. T

    Gehl 6640 Overheating

    When was the hyd, filter last changed? Do you have a lazer thermometer to tell you the actual oil temp when the light comes on ? You could have a bad sensor. .
  14. T

    6635 Gehl starter

    There is a secondary solenoid that activates the solenoid on the starter. It is located on the right side of the frame below the muffler. There are 2 solenoids there; one is for the starter, the other is for the glow plugs or manifold heater.
  15. T

    Bent fork on farm loader

    I have a fork off a Massey Ferguson farm loader. I t is tweaked about 1/2 to 5/8" 5" from fork upright. The fork measures 4 3/4" wide X 1 1/4" thick. Anyone have experience or luck in straightening forks.
  16. T

    Wanted- Factory workshop Manual Gehl 6640E-Deutz BF4M 2011

    Try Memo Parts in Texas. 877-959-2650. They are an aftermarket Deutz supplier. They were very helpful on the last Deutz engine that was giving me fits.
  17. T

    Sizing up a new tilt cylinder? Can it be done with without dealer parts?

    You would need to match the extended length of the other cylinder so that they bottom out at the same distance when you dump the bucket. also the retracted distance should be the same. you will be better off in the long run to replace the damaged parts or a new cyl. if the rod & barrel are bad.
  18. T

    flat faced coupler connection issues

    There is a male tip available that will couple under pressure. They are black in color. you hook this connection first and then you can connect the second coupler, I don't know the brand name; my Gehl dealer sold it to me; wasn't cheap but works good.
  19. T

    TB45 bottom roller

    I have an old Takeuchi TB 45 excavator 1988 vintage with steel tracks. I am looking for a bottom roller. I haven't had any look doing web search. Found some for a TB045 but had a disclaimer that it would not the TB45. Takeuchi part # 02113-90000. Any ideas where to look? Thanks, Terry Z
  20. T

    case 580ck forklift

    The seriel # tag is gone. The only tag is the forklift ser # on the forklift frame. Is the serial number stamped on a housing somewhere? I am not that familiar with case equipment.
Top