• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. K

    CAT Grader 140H

    Any warning lights come on when this is active? Does articulation the machine make it come and go? Those machines are famous for broken wires in the articulation joint. As Nige always says a SN would help greatly!
  2. K

    Linkbelt 800LX Electrical schematic badly needed

    S.N. 8912, 2004 year model with multiple electrical issues but no circuit shorts or opens shown on monitor. The service manual is very limited and some wires change colors on the way to the machine controller which is new and properly initialized. Thank you!
  3. K

    D4H LGP - tranny engages but does not move

    The exploded view shows the shaft, bearings,seals etc. and a parts list should be with it. Anyway if we helped please click the like button to show appreciation! Good luck and hope to hear back from you!
  4. K

    D4H LGP - tranny engages but does not move

    Here are linkage parts pages! Enjoy. https://mega.nz/#F!wQIm1CxB!sKQyXbcvhhpg6ndq3_7QXw
  5. K

    D4H LGP - tranny engages but does not move

    50 PSI is too low, could be low oil or a leak, need machine serial number!
  6. K

    D4H LGP - tranny engages but does not move

    Down another 4 to 5 inches! The 6V number is for the test nipples, need machine serial number!
  7. K

    D4H LGP - tranny engages but does not move

    On an 8PB the parking brake valve is bolted to the steering clutch and brake valve down low on the valve. It has a spring and poppet inside that may be the issue. A bad poppet, seat or spring will cause this issue. There are 4 plugs below the ones you saw to remove and install 6V3965 test...
  8. K

    D4H LGP - tranny engages but does not move

    What is the machine serial number?
  9. K

    D4H LGP - tranny engages but does not move

    Box (C) is the steering clutch and brake valve and there should be test ports or plugs on the front to test pressures. I think you will find a problem with the parking brake valve inside that valve.
  10. K

    D4H LGP - tranny engages but does not move

    Those pressures are possible because the filter only supplies lubrication oil. Have you inspected the pump suction screen and filter for debris from a component failure?
  11. K

    D4H LGP - tranny engages but does not move

    By memory that's not possible! I might need to look at a schematic to varify.
  12. K

    D4H LGP - tranny engages but does not move

    Sounds like the brakes are pretty much fully applied and you are driving through them. In first gear you should be able to do that but not in second and third.
  13. K

    D4H LGP - tranny engages but does not move

    Yes check that but I'm still concerned about high oil leakage in a clutch or brake. You do need another gauge because the trans pump pressure can not be less than the P1 pressure! Maybe an intermittent problem also.
  14. K

    D4H LGP - tranny engages but does not move

    Yes, the lever not returning could be at least part of the problem!
  15. K

    D4H LGP - tranny engages but does not move

    Start with the high (left) port which is called P1.
  16. K

    D4H LGP - tranny engages but does not move

    Recheck your pressures in gear, brake pedal released, pull 1 lever half way back to block oil to that steering clutch. Note: the machine might move! Then pull all the way back to block oil to that brake. Next do the same with the other lever! A change in trans pressure of more then about 20 psi...
  17. K

    2010 Cat 252B Intermittent Wiring Issue

    Also the ECM's are under the floor plate and it is very common for rodents to get in there and chew on the wires or for mud to build up and corrode connectors and even corrode through the ECM case!
  18. K

    2010 Cat 252B Intermittent Wiring Issue

    Can you post the machine serial number please?
  19. K

    345b excavator

    Have you tried the backup switches behind the arm rest to see if that makes a difference? Is the green LED on at the front of the machine controller next to the right front of the seat support?
  20. K

    2002 Cat 420D IT ?

    That sounds like a pilot valve (joystick) problem to me!
Top