• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. A

    kobelco coupler

    Im looking for a manual coupler for a 290 , 330 or 350 kobelco . Do not want a hydraulic one. Thanks mike 814 882 5191.
  2. A

    150 kobelco mark iv oil pressure light

    oil pressure My problem with it is the dealer says 50 pound pressure is the high and we are running 80 to 90 at top even after cleaning relief valve according to the mechanical gauge we put in.Why / How do we get it down?
  3. A

    bantum koehring 450 a excavator

    Well it warmed up enough last week that we got it started and brought it home,thanks for the help on what levers and pedals do what.We even managed to leave the building it was in complete intact.My son was running it and says it sure is different from todays excavators so I believe it is going...
  4. A

    150 kobelco mark iv oil pressure light

    I have a 150 mark IV that the oil pressure light has been coming on sometimes,we replaced the sender but that did not help.Then we put in a mechanical pressure gauge, when the light came on it was still in the 40 on idle to 75 full throttle pressure range.Local dealer said 75 was to high that it...
  5. A

    bantum koehring 450 a excavator

    thanks Thank you for you help and if it ever warms up around here we will go try to get it out of the building while leaving the buiding standing .Good luck to all and thanks again.
  6. A

    bantum koehring 450 a excavator

    I just bought a 450 a bantum excavator that is in a small garage .It is suppose to run although battery was dead when I bought it and do believe the man because you can see where they had to fix the wall he took out with boom. Does any one know about the controls on one of these and do the have...
  7. A

    hough cm 60 hydraulic problem

    found problem We pulled the drive shaft to see it the yoke was stripped and no such luck,got it on a trailer and back to shhop and took off torque converter cover and found flange that is suppose to have 6 bolts in 4 were broke and 2 came out.We found the ones that came out and broken half...
  8. A

    hough cm 60 hydraulic problem

    The shaft going to the tranny turns fine but I have no idea what is in the tranny for a coupler, that is someting I was hoping to get some idea here about.It ran fine and we don't want to scrap it over something little but would like to get an idea what we might be getting into.
  9. A

    hough cm 60 hydraulic problem

    Sorry I should have said this is a h 90 cm we bought not a 60.
  10. A

    hough cm 60 hydraulic problem

    Hi I just tried out a loader we bought last week and after loading 2 trucks the hydraulics died, my son was leveling out some gravel not working it hard and it was like some one shut the hydraulics off.We lost everything bucket movement ,no drive and no steering.He said it did not make any...
  11. A

    hough 60 cm

    Hi I just bought a hough 60 last week and treid it out today ,we loaded out 2 trucks and my son went to level out some gravel and the hydraulics died.He said it did not make any sounds it was like someone turn something off. It runs fine but will not move, no bucket or hydraulic funtions or...
  12. A

    540 dresser loader pins

    I have a 540 dresser loader that is a 1987 I belive, it has about 1/4 inch of movement in the lower front half main hinge pin bushing.Does anyone know what is called excessive wear,i don't want to run it till I have to have it line bored but have no idea how thick the bushings are.I know no...
  13. A

    kobelco 150 mark iv

    Thank you for your ideas I think we will be looking at it soon while we wait for other parts.
  14. A

    kobelco 150 mark iv

    I have a 150 mark iv that is makeing a noise in the track drive when its in mud ,It almost sounds like a spline jumping .WE put the bucket on the track giving it a little pressure and power the track you can hear it but sprocket doesn't turn .It move fine normally you would not know anythings...
Top