• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. grvlpt

    NH C185 Fuel solenoid not getting power

    Thanks, I will try that. I also notice a signal about only 10v when I turned the key off. Like to know where that message is coming from. I have a repair manual and will attempt to troubleshoot from it.
  2. grvlpt

    NH C185 Fuel solenoid not getting power

    Can hear it click when jumper wire attached. Changed the larger of the three relays on a hunch, unit started a few times, now the gremlin is back. Any suggestions? Thanks
  3. grvlpt

    case 1085c dies when using turntable cw only

    Good idea. Never done that before but I have the service manual.
  4. grvlpt

    case 1085c dies when using turntable cw only

    I hear no bearing noise altho the turntabe seems a bit "loose" w/o the swing brake on. No work on the swing motor. I have noticed significant looseness in the joystick and yesterday it worked ok. I suspect crossed hydraulic signals from the joystick. thanks
  5. grvlpt

    case 1085c dies when using turntable cw only

    everything else functions, but when the joystick is moved right, the engine dies. After restarting, moving the control ever so slowly to the right allows movement without engine suddenly quitting.
  6. grvlpt

    Case 1085C hydraulic issues

    Correct, the book describes it as a pressure relief valve. The coils on the opposite side are for the pilot control. at least one of them is. Today I disconnected the coils from the harness to check voltage and ground of the harness at the connector, got good readings, noticed the connector...
  7. grvlpt

    Case 1085C hydraulic issues

    Thanks. Today I cracked open the line going from the solenoid valve to the joysticks, then I fired it up and dropped to left control momentarily. Oil was everywhere. I closed the line and messed with some sort of pressure relief or IDK on the side of it. No change. I can put a gage on the...
  8. grvlpt

    Anybody know anything about safety switch on Case 1085C CruzAir wheeled excavator?

    did you ever get it repaired?
  9. grvlpt

    Anybody know anything about safety switch on Case 1085C CruzAir wheeled excavator?

  10. grvlpt

    Case 1085C hydraulic issues

    Thanks again. I did the switch test from the book. I get 24v as advertised on #57 wire but the switch does not always cluck and sometimes it does not break contact when the arm is raised. I will order a new one to be sure. Also, if I rev the engine to almost 100%, sometimes I can raise the...
  11. grvlpt

    Case 1085C hydraulic issues

    Thanks for getting back to me. I could not begin to get the suctions strainers inside the hydraulic reservoir loose, must need something special to get them out, however, the outriggers work and if there was a suction problem I dont think they would work. I have new spin on filters of the...
  12. grvlpt

    Case 1085C hydraulic issues

    I know its been awhile, but this machine functioned as normal for some time and now has started acting up again. Please let me know what I could check.
  13. grvlpt

    Case 1085C hydraulic issues

    Today I started up this machine and it functioned as advertised. I let it run for about 45 min and still worked good. Let it set for 2 hours and still works good. Tomorrow we take it to a job and see what happens. thanks to you all.
  14. grvlpt

    Case 1085C hydraulic issues

    Thank you all for so quick response. I am new at this machine but have factory manuals. Will begin to troubleshoot next week.
  15. grvlpt

    male

    male
    • grvlpt
    • Profile post
  16. grvlpt

    Case 1085C hydraulic issues

    Machine starts easily and moves and stops as it should. At times the equipment does not function, at times it does. Sometimes when its cold it operates properly, other times when its cold it does not. Running the engine at high speed seems to allow fluid into the joystick controls, sometimes...
  17. grvlpt

    accumulator pressure and brake release

    Case 1085C wheeled excavator. Cannot find reference for hydraulic brake accumulator pressure. Takes upwards of 20 min to get low pressure dash light and alarm to quit after startup. Also, when moving, there is the distinct sound of brakes dragging. When parking brake is set, machine will not...
  18. grvlpt

    Anyone know pressure of hydraulic accumulator in case 1085c braking system? I have service and...

    Anyone know pressure of hydraulic accumulator in case 1085c braking system? I have service and parts books but can't find that info. Thanks
    • grvlpt
    • Profile post
  19. grvlpt

    125c moves erratically in forward

    its acting up almost always now and moves forward with any force very little, also, if moving forward and steering engaged, it stops.
  20. grvlpt

    125c moves erratically in forward

    Pilot control valve? When I put the control valve into a forward position, I can feel a slight clunk in the transmission.
Top