• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. G

    John Deere 310b hoe identified

    ok I hooked the lines together, nothing. I pulled them apart and capped them, went back to barley working. I went buy the deere house and picked up the new o rings, 66 bucks later I left. I hate paying for those fancy store fronts. this hoe doesn't seem to have to many hours on it. everything...
  2. G

    John Deere 310b hoe identified

    Well I have a service manual on the way, and an o ring set. I blocked off the backhoe with some caps this evening and fired up the hoe. Well the front end loader still doesn’t work. So I guess I will be checking the relief valve on the front end loader tomorrow.
  3. G

    John Deere 310b hoe identified

    t town you the man, thanks.
  4. G

    John Deere 310b hoe identified

    I have a parts manual, and have been looking to see what the difference is. but so far all I find different is some o rings.
  5. G

    John Deere 310b hoe identified

    The pin
  6. G

    John Deere 310b hoe identified

    I have a 310b I assume was built in 85 by the product I’d tag. I have had an issue with the hydraulics not working. The front end loader would take two or three minutes to raise. The backhoe works faster but nowhere near right. But I could run the backhoe all the way out and still have enough...
  7. G

    tl 140 auxiliary hydraulics, soft start/stop

    I thought about the relief valve, and read up on them a bit. but I ran out of time and took it up to my place in Colorado, it will probable never make it back home. but the start is still pretty rough when engaged at anything above idle, unless I hit bypass. it worked great mowing down all the...
  8. G

    tl 140 auxiliary hydraulics, soft start/stop

    ok I played with it last week, if you tilt all the way back till the machine hits bypass then engage the hydraulics it is nice and smooth on take off. and I can load it down and just disengage the aux hydraulics.
  9. G

    tl 140 auxiliary hydraulics, soft start/stop

    I built a mower to go on my tl140 and it seems to work fine. but the abrupt start and stop of the hydraulics has me worried. I thought about an overrunning clutch built into the drive line, but that will only work for the stops. I read in a sales brochure that says it has electrohydraulic...
  10. G

    Water well drilling with a skid steer

    this got my attention today. i was thinking about using my skid steer to spin it and my excavator to lift or apply down force. http://www.ebay.com/itm/182154246062?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT
  11. G

    liebherr pr712 m

    i'm going to send it off to a computer repair place and see what happens.
  12. G

    liebherr pr712 m

    that was my plan to do some more research, but he jumped the gun to say the least.
  13. G

    liebherr pr712 m

    my buddy found a wire that was not hooked up to anything. it took me a while to find it on the diagrams and it looked to be hooked up to a relay. he hooked it to power and let the magic smoke out of the computer. the dozer only drove on the right side the left side was dead.
  14. G

    liebherr pr712 m

  15. G

    liebherr pr712 m

    I do t think I have a computer diagram It has a coating over everything
  16. G

    liebherr pr712 m

    ok i found a new computer, 8600.00 so that is not happening, i am getting desperate.
  17. G

    Excavator steel track links seizing up when dry

    diesel is all we have ever used.
  18. G

    liebherr pr712 m

    i have a liebherr PR 712 M. the computer has a burnt spot on the board. it runs like a top, blade functions like it should and the under carriage is all but 100 percent. but now it wont move. as y'all know parts are a pain to get. so i was wondering has anyone ever converted one over to manual...
  19. G

    Newbi Dynahoe Owner

    fuel additive??? try some HEAT. i bought a white bottle of synadyne and it gelled on me at -5. ruined a whole mornings work.
  20. G

    Old time operating techniques

    i love these threads
Top