• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. P

    2019 Bobcat T585 fuel starvation

    If Gauge shows empty but still has fuel the it would be the electronic float assembly part # 37 that is sticking or not reponding, i have had mine fail and once i removed the old one i looked at it and it was not registering properly. I cleaned it with alcohol and reinstalled it and it works...
  2. P

    Cat 299D2 stereo wire identification

    It could be a wire going to an RCA headphone jack remotely located? Just a thought. Usually RCA wires are wires within a wire or Coax.
  3. P

    Case430 fuel gauge/sending unit issues

    I have had an issue with the one on my Case SR200, if the unit sits for a period of time the float that rises up and down seams to stick and it would provide false readings. After replacing the original one it happened again so i took it out and cleaned the "ROD" (for lack of a better word) that...
  4. P

    2022 Case TV370B top tilt cylinder pin grease

    My understanding is that the upper pins are a not needing grease and this was done to prevent the operator from rubbing up against them entering and leaving the cab and getting grease on themselves. that's what i was told from the dealer years back.
  5. P

    John Deere 325 Skid Steer hops like a rabbit under load.

    From my family to yours, wishing your Daughter a speedy recovery and hopefully all works out well. We must look after our family first.
  6. P

    259E FRONT DOOR

    You may need a jumper plug for the wiring, the newer unit Sr series have a plug that gets disconnected and a jumper the plugs in to end to bypass the door safeties that are in place so as the unit cannot move with the door open.
  7. P

    JD 240 Starting issues

    I have seen some Case models that when pushing snow moisture gets in to starter and then freezes not allowing it to restart until thawed. In fact, this fall used a small amount self regulating heat tape and wrapped it around the starter of one unit terminated it to a male cord end and the owner...
  8. P

    fender

    Most anything can be removed with a cutting torch, just not sure how easy it would be to reinstall. lol
  9. P

    Rebuild #2 Has Started Case 1845c

    I do appreciate the work your doing and looking forward the posts. If required it sounds like she would good for touch painting if required.
  10. P

    Rebuild #2 Has Started Case 1845c

    Looks good, you will have a his and hers once you're done. Does the better half know how to operate the skid steer? My wife has been hounding me since we bought ours and i still haven't taught her, maybe I'm scared of Job Security?
  11. P

    Rebuild #2 Has Started Case 1845c

    Keep up the good work and please continue posting update picture as regularly as possible, it's nice to see some quality refurbishing happening not just a paint spray rebuild. I look forward to seeing the finished project. One question I have, Do you resell these and is so do you get back your...
  12. P

    Help: what kind of corrosion/chemical is this???

    I've seen similar effects on steel from Cattle/Dairy chicken and pig farms. it could be caused by the ammonia from the urine while cleaning corals pens or the machine was stored in the barns. Also as Nige mentioned it could from salt air or from an agricultural chemical supplier. A few years...
  13. P

    CASE 1845c Restoration. Follow my progress!

    Very well done, do yourself a favor and never try to figure out what you have invested in time and materials. Enjoy your "NEW" unit.
  14. P

    Bobcat S300 Rear Main Seal

    Very well explained and I'm sure many members will be happy to see such a post.
  15. P

    Looking at skid steers???

    If the brush cutting is just a once in while occurrence, (once every 5 to 10 years), you might be better off hiring it out and not worrying about the dual hydraulics, and the brush cutter attachment purchase or rental. You could then look at a good used machine without the dual Hydraulics and...
  16. P

    Case 450 battery problems

    How old is the Battery? Sometimes the battery plates work loose within the case and don't provide the correct voltage. Did you try replacing the battery with a new one and see if the problem persists?
  17. P

    anyone have experiance with a bobcat scraper?

    I've seen it used on Ice in a parking lot, but i haven't seen them use it for few years, that tells us something doesn't it. I"ve been told it work good for removing ceramic tile on concrete in a large area.
  18. P

    863 hydraulic info needed

    Be careful using a large Pipe Wrench, you want to make sure that grab from different locations so as not to oval the pipe or ftgs. Mapp gas may not be hot enough, Oxy Acet. is better.
  19. P

    Cat D series backup Camera??

    A few year back. two or three, I had installed a Voyager AOM713 on my Case SR200. I'm happy with the Camera but Yesterday the cheap plastic bracket that mounts to monitor broke. It can be fixed with a piece of steel and a little ingenuity but why would they use a piece of S--t plastic piece...
  20. P

    New Holland C232 Backup alarm

    I've seen some that have had a small screw driver pushed through the speaker portion and it has quieted down the noise. Angry neighbor at a job site working nights.lol:rolleyes:
Top