• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. VoodooMojo

    Genie Z45-22 very slow speed

    Andrey, how does this machine Steer? Is Steer slow as well? Although these older units do suffer from voltage drop, you may want to eliminate the hydraulic system first. It will be easier accomplished than electrical diagnostics. The fact that your drive is working good suggests that the...
  2. VoodooMojo

    genie tmz50/30 fault code 0010

    0010 is a communication fault between the upper and lower control boxes. If you are a fortunate person, it will be in the cable running from upper to lower. Try plugging the Upper Controls directly into the Lower Control Box. This will eliminate the cable installed on the boom. Also suspect is...
  3. VoodooMojo

    Genie z45/25 Blinking red light on ground control panel

    If Ford Dual Fuel the answer is no. If Deutz Diesel the answer is no.
  4. VoodooMojo

    Genie z45/25 Blinking red light on ground control panel

    serial number?
  5. VoodooMojo

    genie tmz50/30 high idle solenoid

    3 questions: Model and Serial Number? Hatz Diesel or Honda Gasoline? Have you tried to connect the Throttle Solenoid directly to the 12 volt DC power source? This would be at the 175 amp fuse F11 or at F9 10 amp fuse connecting at the 12volt terminal at the Start Solenoid. Be informed that...
  6. VoodooMojo

    Genie Z135/70

    PCON, TCON and SCON will all need upgrading. There are 3 outstanding service bulletins requiring completion for serial number Z13507-385: 120007 (Z-135 CONTROL SYSTEM UPDATE) 140019 (PLATFORM LEVELING) 150002 (SECONDARY BOOM ANGLE SENSOR) Please contact your local Genie service provider...
  7. VoodooMojo

    Genie s 125 boom will not extend

    a couple things: what all functions properly? will the primary boom raise and lower? Jib functions work? platform and turntable rotate functioning? will it drive, steer? when turned on at the ground controls, what version software is displayed on the screen? scroll through the menu to check boom...
  8. VoodooMojo

    jlg 40ha platform controls problem

    it sounds as though one of the two micro-switches inside the footswitch is hanging up. One switch manipulates the B minus and the other the B plus. if one hangs up there will be a direct short and the circuit breaker will trip....check this out first...
  9. VoodooMojo

    jlg 45 ha platform controls cut out/ engine reeving problem

    Clicking noise when you step on the foot pedal or when you hit a specific controller / switch? You may want to open the upper control box to see if it is the circuit breaker tripping...it could be in the throttle circuit....well, we have to begin somewhere....!
  10. VoodooMojo

    Genie Z60/34 operates fine but will not drive

    Deutz, Ford or Perkins engine? Is the Platform positioned between the two wheels at the non-steer end of the machine? Are there any Fault Codes present at the Control Card inside the Upper Control Box? Is the Alternator putting out the desired Voltage at the correct Frequency?
  11. VoodooMojo

    Genie 1999 Z45/25 wont move.

    We will need a voltmeter, a hydraulic pressure gauge (0 to 5000psi) and about an hour of time. We need to see where voltage is present and not. Do you have the schematics for this machine? If not: http://manuals.gogenielift.com/Parts%20And%20Service%20Manuals/servZbooms3.htm We will...
  12. VoodooMojo

    JLG 40E boom synchronizing

    Just a couple questions to start: Which two hoses were replaced? There are reducer fittings on some cylinders that are needed to create a pressure difference to activate the counterbalance valve. Did the problem happen immediately after replacing the hoses or after awhile? Also, was...
  13. VoodooMojo

    Sullair blowing oil

    inspect the areas in the circles. The large one more than likely is the valve in question. It should keep the pressure in the receiver from blowing back through the air-end. If it is not a valve then the smaller circle could contain an internal valve that checks this pressure. Somewhere...
  14. VoodooMojo

    Sullair blowing oil

    in this photo: 18 looks like a bolt 23 and 26 look like elbows 36 and 46 not to be found
  15. VoodooMojo

    Sullair blowing oil

    yes FSERVICE...many drinks!! For awhile I would run watchdog over a wagontrain of 6 1600cfm Sullairs....5 running and one shut down for servicing or repair. We would set them up in a circle, wide open, supplying factory air for large manufacturing operations when their factory air source was...
  16. VoodooMojo

    Sullair blowing oil

    what is #31?
  17. VoodooMojo

    genie GTH-5519 leveling cylinder

    there is a high cracking pressure involved with this circuit. Some boom movement is expected but will the engine die while raising or lowering the main boom when the engine is at idle? The leveling cylinder you speak of is the one at the pivot end of the boom behind the operator or at the...
  18. VoodooMojo

    Sullair blowing oil

    the separator element in the receiver will not be your issue...that can only cause oil coming out the air discharge end. The more I think about these rotary screw machines the more i remember my days on Sullair, Worthington, Garner Denver, Joy, Sullivan etc compressors. The valve I speak of...
  19. VoodooMojo

    Sullair blowing oil

    the hose and valve I speak of is the large (probably braided) hose that runs from the bottom rear of the air-end (compressor screw) to the receiver. The check valve will be at one end or the other of the hose. I was looking for an image of it on the web last night but, alas and alak, I found...
  20. VoodooMojo

    Sullair blowing oil

    Is this the Leroi?
Top