• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. R

    2015 Hino 258 RPM run away

    I don't quite understand who your calling and for what your calling them for?
  2. R

    2015 Hino 258 RPM run away

    Under the dash on the passenger side is a black box. That is the bulk head and all the harness connections are in there. The main harness enters from the top of the box from behind the dash. water leaks from the windshield and onto the harness, then runs down the wires and soaks the connectors...
  3. R

    2015 Hino 258 RPM run away

    FYI. That was not the fix.....Did the same thing in the next rain. Turns out water leaked onto the harness plug on the passenger side. That plug was associated with the TPS and pedal. Dried the plug and used dielectric grease on all connections. Good to go now.
  4. R

    2015 Hino 258 RPM run away

    Fuel economy has not increased
  5. R

    2015 Hino 258 RPM run away

    Thanks to all who tried to help, I really appreciate it!
  6. R

    2015 Hino 258 RPM run away

    Originally they said just unplug the EGR and the DEF pump. They were probably assuming that all the associated equipment had been removed as most do.... But it was all left in place and a new exhaust was routed around it. That being said, they said to unplug everything associated with the...
  7. R

    2015 Hino 258 RPM run away

    Thanks for this info!
  8. R

    2015 Hino 258 RPM run away

    Truck ran for 2 - 10 mile trips then a 200 mile round trip.
  9. R

    2015 Hino 258 RPM run away

    I'm wondering if anybody has had this happen to them because of a faulty accelerator pedal assembly? I'd hate to change of $500 pedal and that not fix the problem
  10. R

    2015 Hino 258 RPM run away

    Okay, I have a problem with my 2015 Hino 258 rollback tow truck. Issue started yesterday. When I start up the truck after about a minute of idle the engine RPM instantly goes to 3000, no way of stopping it, I just need to turn the key off. It only does this when in neutral. Another example is...
  11. R

    2005 Nissan UD 2300 limp mode

    I believe is gear driven
  12. R

    2005 Nissan UD 2300 limp mode

    From what I can tell, the JO8E has a gear driven timing system.
  13. R

    2005 Nissan UD 2300 limp mode

    The check engine light flashes 8 times pauses for the allotted amount then flashes eight times again there's no single Flash or other flashes before or after that would indicate it's any other number. I took a video but I could not upload it. I don't know if it's a timing chain or gear driven I...
  14. R

    2005 Nissan UD 2300 limp mode

    Hello I have a 2005 Nissan UD that is going into limp mode I have followed the manufacturers instructions to activate the check engine light flash sequence I have grounded the engine diagnostic wire then turn the key to the on position the check engine light will flash 8 times however there is...
  15. R

    Help: old yale-er lift cylinder removal

    Yup, basically exactly what I had to do. Figured the only way to get to those caps was to lift it higher then I had it. Then I seen your reply. LOL. Thanks for taking the time!
  16. R

    Help: old yale-er lift cylinder removal

    So it's time to put seals in my yale, it's a GC030UA I think from the mid to late 70's. I've not dealt with this type of cylinder before where it is attached near the bottom on pivot pins. How do I get it separated from the gantry? I am trying to up load a photo but its not letting me?
  17. R

    International engine swap?

    Hello, I have a 2001 international rollback with a DT530 with a standard transmission behind it, engine went bad.... I have a cummins L10 on the side. I've heard the internationals came with the L10's, has anyone ever swapped one into a DT truck? Thanks!
  18. R

    No start. Komatsu PC50

    Okay, update. Machine runs! turned out being the starter after all. I guess being in Hawaii and all of our humidity caused 2 of the brushes in the starter to get stuck out/off the commutator with only 2 contacting the commutator, there was not enough power to turn the starter. I figured this...
  19. R

    No start. Komatsu PC50

    2006 PC50mr-2 The other day the dash/display was randomly beeping while I was operating. I noticed some moisture under the cover. I removed it and dried it. Re-installed it, and it seems fine, all the functions work, went to start the machine and I just get a relay clicking when I turn the...
  20. R

    Internationl 100E track loader seal kit?

    Thank you very much! I placed my order the next day, they shipped it u.s.p.s. priority mail (saves a lot when sending to Hawaii) it arrived 2 days later. Friendly excellent service! BTW. $14.50 per kit! Thanks again!
Top