• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. J

    320B governor actuator

    Want to replace my governor actuator its mounted under the engine. Old one had top cable to top of injection pump lever and bottom cable to bottom lever but my parts book shows cables vise versa so a little confused anyone know what is proper hook up.
  2. J

    320B excavator throttle

    Does any one have diagram on how to remove throttle dial intermittent connection when I wiggle the dial it works assuming dirty or failing.
  3. J

    sweeps

    need to put sheet plate on top of my open sweeps wondering what thickness and if it should have a cross break done to stiffen it.
  4. J

    v brush cutter

    Thinking about a brush cutter don't know much about them pros and cons.Been tramping it down then piling with cat.
  5. J

    trans temp

    My D6H LGP with 15 ft blade trans runs at 200-205 F is that normal op. temp drops quick when i stop engine runs 185 F.
  6. J

    injection pump

    had my injection pump rebuild on 315B cat excavator started a couple times fired right up but now it spins over probably 5 times before it starts runs good never a issue before the reason for rebuild was it was starting to flutter when it would go to idle cat rebuild engine 2 years ago
  7. J

    320B swivel

    My one track travels slower than the other one so i want to remove swivel to reseal.My question is do i have to drain hydraulic tank to remove hoses.
  8. J

    320b wiring harness

    Was having throttle issues came down to replace wiring harness H and A can't find it in the schematic or parts book anyone know about these
  9. J

    320BL engine oil dipstick

    do most of these excavators not show right in the morning mine shows add or below wipe it off try a again and it shows full my 315BL is the same engine oil
  10. J

    new cam and lifters

    rebuilding 3046 cat/Mitsubishi engine putting new cam and lifters in was told with new cam and lifters break in is more important with new cam and lifters did my 320 last year but old cam and lifters were good.
  11. J

    breaking in rebuilt engine

    whats a good way to break in rebuilt engine cat 3066 excavator.
  12. J

    wrist twist bucket

    I have a wrist twist bucket on my 315 cat have had it for about 5 years, now it only tilts one way now when i try to tilt the other way the hoses tighten up but it wont move .I have a thumb on it so if i want to use the bucket i just turn two ball valves and then i can use the bucket thumb...
  13. J

    D6H hyd. oil

    1987 D6H my hyd oil was low cant find any external leakes is it possible for it to leak into the bell housing it is diff steer its a 5HF
  14. J

    320B engine

    what to do a rebuild on my 320b cat excavator has a 3066 do liners have to be replaced to i am new to this.Starting to use oil plus a few leaks so figure its time 13000 HR.
  15. J

    87 mack 97 D6H

  16. J

    320 BL radiator

    I have a aftermarket radiator in my excavator hot days it wants to heat if i turn air conditioning off, i can manage it then, had rad shop check rad last year he said it had good flow so i put new thermostat in he also said he wasn't sure what cat rad was compared to this one it is a 4 core it...
  17. J

    320BL engine

    Thinking about rebuilding the motor in my 320 3066 since this is a sleeve less engine what are the chances of haveing to get it rehoned starting to use oil 12000hrs. Its also abit hard starting when it gets colder outside so thinking its getting worn my 315BL approx same hours fires right up.
  18. J

    D6H air conditioning

    My air conditioning works when i first start using the cat. Run the cat for awhile turn temp down or turn fan on off then it wont work till you let machine cool down overnight.put new pump on last year worked fine last year pump was a jobber.
  19. J

    Scraper for D6H

    what size scraper could a D6H handle series2 LGP never have had anything to do with scrapers.Are they hard on trnsmission.
  20. J

    Governor calibrate

    Replaced my governor actuator on my 320b cat excavator trying to calibrate it but hangs up on 7 go,s to about half throttle and stays there with no codes have tried all sorts of positions of cables no difference it was an after market one.It is the two cable one.
Top