• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. D

    1994 case 1845 skid steer tilt bleeds over and trans spool leak

    Anyone know a good alternate resource for the hyd temp switch that fits into the R/S wheel motor line or the hyd pressure switch that goes into the top of the transmission R/S. Both of these activate the dash display, one for hyd overtemp and the other hyd low pressure. Or know the approximate...
  2. D

    1994 case 1845 skid steer tilt bleeds over and trans spool leak

    Just wanted to follow up. Alrman thanks so much, I would pay you if I could. Your knowledge is ridiculous. I replaced those o rings in the secondary relief block. They were defiantly torn. Wasn't bad to get to with bucket up and blocked. That fixed bucket bleed over. and the other spool seal...
  3. D

    1994 case 1845 skid steer tilt bleeds over and trans spool leak

    So if I cap off that line to that block, that should tell me if that’s leakage? Block looks like a pain to get to. Thx again for help.
  4. D

    1994 case 1845 skid steer tilt bleeds over and trans spool leak

    #1 I do not have serial # due to tag missing at left knee panel, fell off years ago. If there is another way to detect which machine let me know. I can take picture of valve if that works. As far as bucket roll back, absolutely not. I did pull checks last night , all looked fine...
  5. D

    Case 1845C leaking on top of tandem pump

    WHERE DID YOU BUY THIS SEAL KIT?
  6. D

    1994 case 1845 skid steer tilt bleeds over and trans spool leak

    Im sure this has been covered but I couldn't find a thread that pointed me in the right direction. This will be simple for many. Alrman? #1 tilt bleeds over - I have rebuilt cylinder's and caped off to verify cylinder's not leaking, so im looking at control valve. I assume, from what ive...
  7. D

    94' Case 1845C drive problems, please help

    need to follow attachment on pg 1 of this thread from alrman, looks like your press drop is too much in one direction. I would swap those big reliefs from side to side, all 4 of them, then if no help swap wheel motors then if no help pull transmission. Make sure that orface is clear and the...
  8. D

    94' Case 1845C drive problems, please help

    I agree with mel pump group is most likely worn. Be nice to put guages on there first to look at charge press and pump press prior to disassembly, and look at those large relief valves on that side (if suspect (swap to other side see if weakness follows). Then if no help there pull pumps, Its...
  9. D

    1845c wont hardly move when warmed up, either side, unless lowering bucket then goes

    need a little input on something When i seperated the halfs, alum. charge pump housing in tight so i removed the big fitting( is that inlet side(comes from filter?) to get to the back side of housing and charge pump alignment pin was laying there didnt know where it came from till i knocked out...
  10. D

    1845c wont hardly move when warmed up, either side, unless lowering bucket then goes

    charge pressure 160psi in neutral? Tried shimming spring with no increase, so guess charge pump bad? Pulling trans. out tonight.
  11. D

    1845c wont hardly move when warmed up, either side, unless lowering bucket then goes

    Where is the charge relief, I remember the 4 reliefs that come in from the sides (2 on each side)? Thanks
  12. D

    Help quick just got home & kid stuck in 247B with bucket up right joystick inop

    tlup right on It was the door switch. Guess I was wrong when i said it wouldn`t track with door open. Looks as if that switch is all that controls hyd. Thanks again, that what makes this site so great.
  13. D

    Help quick just got home & kid stuck in 247B with bucket up right joystick inop

    From memory, this particular rig won`t move or lift if any of the failsafe`s arn`t complete. Don`t know if there dual pole swiches though, (meaning that the door could close and make circut for traction but not lift). Pulled joystick boot up and no electric there just pushdown pins that the...
  14. D

    Help quick just got home & kid stuck in 247B with bucket up right joystick inop

    Ive got nothing on this rig, dont even know where to look for codes. Not my rig just use it from time to time along with a few other guys & im the mechanic so i usualy get the problems. I just havent had to get into this thing yet but its getting older so I better learn. Im told cat is very...
  15. D

    Help quick just got home & kid stuck in 247B with bucket up right joystick inop

    Found valve in rear. Thanks a bunch. Now can anyone give me some advice on this inop r/h joystick? Tried unhooking battery, bouncing rig around, recycling lap bar, door, and brake release, no help. It must be seeing these switches because machine tracks around. Switched relays below seat and...
  16. D

    Help quick just got home & kid stuck in 247B with bucket up right joystick inop

    seriously, please advise, door wont open. Whats up with thing back glass tough to get out? Anyone know most common problem with inop right stick Thanks
  17. D

    1845c wont hardly move when warmed up, either side, unless lowering bucket then goes

    Forgot what i use to know Being that its both sides { equaly weak}, is it likely that its just charge pump or am i looking at rotating groups on both pumps? I cant remember a separate charge pump in there. Thanks
  18. D

    1845c wont hardly move when warmed up, either side, unless lowering bucket then goes

    Tractor has some power when cold but once warms up wont even move when rasing bucket, but seems to move good while lowering bucket. Please explain, and i hope it doesnt entail rebuilding trans I did right side some time ago when this tractor had no power on one side.Kinda sounds like charge...
  19. D

    Anyone had cyclender head valve breakage on 963 cat?

    more info The head has been off before but not sure if was surfaced. Valves may have been a little tight "mabye couple thou". How much piston to valve clearance is acceptable? I build drag race engines and we accept .080 piston to valve at 8000rpm so I would think these things spinning, what...
  20. D

    Anyone had cyclender head valve breakage on 963 cat?

    Its a 1994 963 A model. This time it broke an intake valve, wow. I think it was an aftermarket part, mabye the problem huh.
Top