• Thank you for visiting HeavyEquipmentForums.com! Our objective is to provide industry professionals a place to gather to exchange questions, answers and ideas. We welcome you to register using the "Register" icon at the top of the page. We'd appreciate any help you can offer in spreading the word of our new site. The more members that join, the bigger resource for all to enjoy. Thank you!

Search results

  1. H

    Genie S-65 Engine start up problem

    Been searching Switch to propane, electric 65psi gasoline pump shut off, ( computer controlled injector timing stays on, spark timing stays the same but there is no gas to injectors.) The person trouble shooting said , have seen problems when tank runs out, dirty fuel filter, or the manifold...
  2. H

    Genie S-65 Engine start up problem

    Steve Years back I found a Ford motor company service manual on the internet which explained the function of these sensors, setting up the computer for start up operation of the the engine. They are part of the timing and fuel richness system and when the computer gets this information , the...
  3. H

    Genie S-65 Engine start up problem

    Steve After I got the sensor problem fixed, . I put on new Map sensor and ignition coil packs. I have those Ford part numbers. . Bob
  4. H

    Genie S-65 Engine start up problem

    Steve Have a 1999 S65 with with LRG 425EFI fuel injected. Read my earlier posts under ACHD21A. Engine Coolant sensor located on water thermostat housing. This sets the ignition timing and rich-lean settings to the computer for initial engine startup. These settings change as the engine comes up...
  5. H

    where to find a new guage

    http://www.stewartwarner.com/en-US/Products/StewartWarner/Product-families/Gauge-Line/Temperature-Gauge-%E2%80%93-Transmission-Oil-(electrical)--P-N-122269.aspx Stewart Warner has electric and standard gauges. Don't know if the JD digital read out or is a standard round panel mount. Gauge...
  6. H

    Battery & Cables - 1991 D4H Series II

    50 years of battery and cable problems on farm tractors, combines, trucks, and my dozer equipment. I attach the ground lug directly to the starter case. I remove a starter mounting bolt to engine case frame, clean everything, ground lug at that point, and tighten down good. This gives me the...
  7. H

    Fiat Allis 16B

    My ACHD21A books recommend ATF in transmission and wet steering clutch system and that is what I use. Bob Ohio
  8. H

    Genie s-65 boom lift not running after startup

    Have had same problem. It is the thermistor type coolant sensor located next to the water temp sensor. Has 2 wires coming out of it. What it does, at start up, the computer system is an open loop, this sensor sends info to the computer about water temp which sets the fuel richness and ignition...
  9. H

    Genie S60 idle surge

    From my past experience with IH diesels on my farm equipt, idle surging can be smoothed out by adjustment of spring tension on the connecting linkage on the out side of the injector pump. Did a search on your engine and found several sites with manual download information but didn't look at any...
  10. H

    New Toy

    Have had water in piston before. Take value pan cover off and open each exhaust valve 1/2 to 1 turn, just enough to know each valve is unseated by a 32nd to 16th of inch. If engine is free, will eliminate hydraulic lock. Roll it thru by hand. Bob ACHD21a
  11. H

    Fiat allis 14c emergency

    http://www.craneandtractor.com/default.htm Good operation Bob ACHD21A dozers
  12. H

    Terex TB44 Diesel Manlift

    40 years plus of starter issues on farm tractors, combines, dozers, and trucks, and a Genie S-65. Starter problems. Starter brush holders that are rusted and weak spring tension, melt down of wiring in side of starter, Corrosion problems in side the battery cable lugs, Solenoid internal...
  13. H

    TD8E won't start

    Here is a link to another site about the adjustment of the linkage adjustment to the D239 injector pump for Start, Run, Stop set up. Read the second post by Fromjb2. Hope this helps. http://www.ytmag.com/cgi-bin/viewit.cgi?bd=farmall&th=571269 Bob Ohio AC HD21A
  14. H

    ALLIS CHALMERS HD6E What Year, Any Help ?

    I had a 5, most likely a dry clutch and a 4 cylinder Buda engine. Check the final drive oil levels and also look for seal leaks on the rear axles at the outboard axle carrier bearing or oil dripping down the inside of the sprocket on to the inside of the tracks. A good old stout machine, little...
  15. H

    650J Over Heating

    Also check the bottom radiator hose. Have had rust and flakes build up over time and solidify and partially block the lowest part of the bottom hose.
  16. H

    Fiat Allis 16B

    HD21P Junk heap Here is an HD21P I went to look at, they said it need some engine work and could be bought cheap. This operation had a big clay pit and the dozer owner was pushing clay for him. It had a low time AC 25,000 engine in it that had came out of a generator unit. The old man said...
  17. H

    Fiat Allis 16B

    My Allis, manpower shifter Been playing with picture posting test site This is my best of three 3 HD21s I have. The tracks are excellent, the sprockets and blade push arms are off a C model 21, the engine is a low time rebuilt 25,000Mark 4 engine. Rebuilt a new exhaust stack for it. Was...
  18. H

    Test

    cccccccc hope this works
  19. H

    Fiat Allis 16B

    Will get some pictures when I figure out how to post them on this site, looked at picture posting yesterday, will try it later. Nutwood My 21 friend , had some land and always joked , take the HD21P and dig a big hole, take the blade off, run the 21 in the hole, my casket laying across the 2...
  20. H

    Fiat Allis 16B

    Hovis They are open 8 to 5 EST. Maybe open Sat? I have never worked on a 16 and nothing major on my HD21s. I have a Case 850 back hoe which would pick or drag most parts off my 21, except the engine. To be safe, engine pull would need a track hoe or a wrecker with a jib boom. One area...
Top